Parts for Electrolux EI28BS56ISC: 09 - Shelves Parts

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This slide crisper cover is the glass shelf that sits above the refrigerator crisper drawer, helping protect produce and keep cold air circulating. It restores a smooth sliding surface and a finished interior appearance. What it does

• Replaces a cracked, chipped or missing glass cover that sits over the crisper drawer
• Provides a stable, low-profile shelf for storing fruits and vegetables
• Allows the crisper drawer to slide smoothly when in place
• Helps keep food separated and contained, reducing spills onto lower compartments

• One slide crisper cover

• Remove food and the crisper drawer before installing to avoid damage or injury
• Lift the old cover straight up to remove; set the new glass into the tracks so it seats evenly
• Handle glass with care and wear gloves to protect hands from sharp edges
• Check tracks for obstructions or damage before forcing

This genuine replacement screw secures panels and small components on select appliances, restoring fit and reducing rattles or loose parts. It's a direct-fit fastener where the original #8-18 x 3/8 screw is missing or worn. What it does:

• Fastens trim, panels or brackets to appliance frames and components
• Restores secure fit to stop rattling or misaligned parts
• Replaces stripped, rusted or missing screws that prevent proper assembly
• Matches original thread size and length for correct engagement

• Use the correct driver and engage threads straight to avoid stripping
• Do not overtighten; stop when the part is snug and secure
• Replace any damaged mating hardware for best fit
• Unplug the appliance or shut off power when accessing internal fasteners

This support is a molded mounting bracket designed to secure and stabilize appliance components, helping keep parts properly aligned and preventing sagging or movement during use. Durable plastic construction for reliable long-term positioning. What it does:

• Secures panels, assemblies, or internal components to the cabinet or frame
• Keeps parts aligned to prevent binding, rubbing, or uneven wear
• Supports weight to reduce stress on fasteners and adjacent parts
• Helps restore original fit and function after breakage or loss

• One support mounting bracket

• Disconnect power and, if applicable, water before beginning any repair
• Confirm correct orientation and seating before fastening; use factory screw locations
• Use appropriate, non-stripping fasteners and do not overtighten
• If the original part is damaged, remove all debris before installing new support

This OEM Replacement Part is a water filter designed to fit most models of Electrolux side-by-side and French door refrigerators. Its primary role is to provide clean and fresh-tasting water for drinking, cooking, and ice-making.

The filter's reduction rates significantly decrease a range of contaminants including Cysts (99.99%), Class 1 Particulates (99.10%), Turbidity (97.80%), Aesthetic Chlorine (97.40%), Lead (99.30%), Mercury (96.60%), and certain herbicides and pesticides. The filter operates at a flow rate of 0.5 GPM with a max pressure of 100 psi and a max temperature of 100 F. It has been tested and certified to ANSI/NSF standards 42 and 53, underlining its quality and performance.

This filter, measuring approximately 8" x 2.5" x 2.37", has a simple push-in installation process that requires no special tools.

This filter release button is the push-button used to release and remove the refrigerator water filter housing. It restores simple, one-handed filter removal so you can replace your water filter cleanly and quickly. What it does:

• Replaces a damaged or worn filter-release push button that no longer unlatches the filter housing
• Allows the filter cartridge to be released from the housing for regular replacement
• Helps resolve symptoms like a stuck, loose, or non-responsive filter release mechanism
• Fits into the filter housing assembly and engages the release latch when pressed

• Disconnect power and shut off the water supply before servicing the filter area
• Remove any trim or access panels per your refrigerator manual to access the button
• Snap or fasten the new button into the housing until it engages; avoid forcing parts

The Refrigerator Water Filter Base is an OEM part for Frigidaire refrigerators. It holds the water filter in place and provides a secure connection to the water supply, ensuring clean and filtered water flows through the refrigerator.

Causes of a bad water filter base can include wear and tear over time, damage from improper filter installation, or issues with the water connections leading to leaks. Additionally, mineral buildup from hard water can affect the performance and integrity of the base.

Symptoms of a bad water filter base include:

• Water leaks around the filter area
• Poor water flow or reduced water pressure
• Filter not fitting securely or falling out
• Unusual tastes or odors in the filtered water

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This crisper cover trim restores the finished edge around the refrigerator crisper cover for a clean, factory appearance and proper seating. It replaces damaged or missing trim to help the crisper cover sit securely. What it does:

• Replaces the trim piece that finishes and protects the crisper cover edge.
• Helps the crisper cover seat correctly and reduces gaps where debris can collect.
• Restores cosmetic appearance when the original trim is cracked, worn, or missing.
• Prevents minor rattling or shifting of the crisper cover caused by damaged trim.

• Remove food from the crisper area and slide out the cover to access the trim.
• Align trim with the cover edge and press until clips or tabs engage; do not force.
• Inspect mounting clips—if they are broken the clips must be replaced for a secure fit.
• Handle glass or plastic covers carefully to avoid breakage.

This beam-style crisper cover is the glass shelf that sits above the crisper drawer, providing a flat support surface and helping contain spills while keeping produce organized. It restores the shelf surface and proper crisper function. What it does:

• Replaces a broken or missing crisper cover to restore a stable shelf over the crisper drawer
• Helps contain spills and prevents items from falling into the crisper
• Supports produce and other refrigerated items above the drawer area
• Works with the refrigerator's crisper beam/track system to maintain proper clearance and operation

• One crisper cover (beam-style) as shown

• Always unplug the refrigerator or shut off power before servicing interior components
• Remove food and any items from the shelf area before installation
• Handle the glass carefully; lift straight up/out from the tracks or supports and slide the replacement into position
• If the cover uses plastic clips or rails, inspect and replace damaged hardware to ensure a secure fit

This genuine replacement spring provides the tension for the refrigerator water/filter release rod so the filter stays secured and releases correctly. Restores proper filter engagement for smooth insert and removal. What it does:

• Applies tension to the filter release rod so the filter locks and ejects reliably
• Helps prevent the filter from slipping or failing to latch
• Reduces binding or sticking when inserting or removing the filter
• Works with the filter housing release mechanism to maintain normal operation

• One filter release rod spring

• Disconnect power to the appliance before servicing; shut off water if accessing the water/filter area
• Remove the filter housing cover per your model's service instructions to access the spring
• Springs can be under tension—wear eye protection and handle carefully