Parts for Frigidaire DGHF2360PF8A: 05 - Shelves Parts

This replacement screw secures appliance components in place. Use it to replace a missing, stripped, or rusted fastener so shelves, handles, panels, or brackets stay properly mounted and the unit operates without unwanted movement.

• Fastens components to the cabinet, door, liner, or frame
• Restores a solid fit when the original screw is worn or lost
• Helps eliminate looseness, rattling, or misalignment
• Matches the original hardware for correct fit and thread engagement

• Disconnect power before servicing; for refrigerators, also turn off the water supply
• Align parts and start the screw by hand to avoid cross-threading
• Tighten with the correct driver; do not overtighten, especially into plastic
• If receiving threads are damaged, repair or replace the mating clip/bracket before installing

This replacement shelf restores a stable, level storage surface inside your refrigerator so you can organize food and beverages safely and efficiently. It's designed to replace a damaged or missing shelf and bring back original fit and function.

• Provides a sturdy, level surface for storing containers and groceries
• Replaces cracked, broken, or missing shelving to maintain safe storage
• Helps prevent tipping and spills when a shelf is bowed or unstable
• Signs it may need replacement: visible cracks, sagging/warping, or a shelf that won't seat securely

• Disconnect power and remove items from the affected area before replacing
• Lift out the old shelf; align and slide the new shelf into the side supports until fully seated
• Handle carefully to avoid bending or chipping edges and corners
• The shelf is level and locked into the support rails before reloading

This drain pan collects defrost and condensation water beneath the refrigerator to help prevent leaks and water damage. It replaces a cracked, warped or corroded pan so moisture can evaporate safely. What it does:

• Collects defrost and condensation water that drains from the evaporator/coil area
• Directs water to the evaporator or evaporation area so it doesn't pool under the cabinet
• Helps prevent flooring damage and corrosion caused by leaks
• Common symptom: visible water or puddling under or behind the fridge
• Common symptom: musty odors or visible corrosion around the base

• Disconnect power to the appliance before starting any work.
• Many installs require removing the lower access panel or toe-kick and carefully sliding the cabinet forward; support the unit as needed.
• Handle edges and mounting tabs with care to avoid cuts; replace any worn mounting clips or seals.
• If corrosion or other damage is present, inspect surrounding components for related issues.

This right-hand support is a small interior bracket used in select refrigerators to secure and stabilize the matching component on the right side. Replacing a cracked or missing support helps keep shelves and covers level and in place.

• Provides right-side support and alignment for the associated interior component
• Helps keep shelves/covers stable; prevents wobble, sagging, or unexpected drop
• Common signs of failure: broken tabs, cracked plastic, loose fit, or a missing support
• Replace if damaged from impact, overloading, or age

• Unplug the refrigerator and remove items to access the area
• Remove the related shelf/cover and retain any screws or clips
• Transfer and reuse the original mounting hardware if required
• Align the new support in the same orientation; secure firmly and confirm level before reassembly

This left-hand support secures and aligns the corresponding shelf or drawer assembly inside the refrigerator, helping it sit level and operate smoothly. Replace a cracked or missing support to restore proper fit and function.

• Provides structural support on the left side of the mounted assembly
• Maintains level alignment to prevent binding, rubbing, or sagging
• Helps drawers/shelves open and close smoothly when intact
• Common signs: uneven or sticking operation, tilting or dropping, visible cracks or broken tabs

• Disconnect power and remove items from the affected area before servicing
• Remove the shelf/drawer; release locking tabs or remove any fasteners holding the old support
• Position the new support on the left side and reuse existing hardware if required
• Smooth operation before reloading

This shelf channel is the metal/plastic support that secures and aligns a refrigerator shelf or door bin, helping keep stored items stable and properly positioned. It restores proper shelf fit and prevents sagging or misalignment. What it does:

• Provides a secure mounting track for a refrigerator shelf or door bin
• Supports shelf weight to prevent bowing, shifting, or falling
• Keeps the shelf aligned so items sit level and doors close smoothly
• Helps restore original shelf fit after damage or wear

• One shelf channel mounting piece

• High-level replacement; inspect adjacent clips and fasteners and replace if damaged
• Use proper hand tools; avoid overtightening to prevent cracking
• Disconnect power only if working near electrical components; otherwise power removal is not typically required

This shelf channel is the replacement mounting rail that supports and secures a refrigerator shelf, restoring stable shelf alignment and load support. Use it when a shelf slides out of position or the mounting rail is cracked or bent. What it does:

• Provides the mounting surface and guide for a refrigerator glass or wire shelf
• Restores proper shelf alignment and prevents sagging or uneven seating
• Replaces damaged, cracked or bent shelf rails that allow shelves to shift
• Helps maintain safe storage by keeping shelves locked in place during use

• Basic hand tools required; follow the refrigerator's service diagram for exact removal and replacement steps
• Support the shelf when removing the old channel to avoid dropping or damaging the shelf
• Disconnect power (or unplug) the appliance if working near electrical components or lighting
• Replace any fasteners, clips or adjacent trim that are damaged to ensure proper fit and secure mounting

This shelf channel mounting bracket secures the shelf channel to the appliance cabinet so shelves stay level and stable. It replaces a broken or worn mount to restore proper shelf alignment and support. What it does

• Secures the shelf channel to the cabinet frame so shelves sit flush and don't tilt.
• Prevents shelf movement or sagging caused by a loose or cracked mount.
• Helps maintain safe storage by keeping items from sliding off tilted shelves.
• Fits where the original channel mount has cracked, worn, or snapped.

• Designed for simple replacement—remove the shelf and channel to access the mounting bracket.
• Use appropriate hand tools; avoid over-tightening fasteners which can crack plastic components.
• Disconnect power and remove stored items from the shelf area before beginning work.
• If mounting locations are damaged, assess surrounding supports; replace any additional broken hardware.

This slide replaces a worn or broken drawer support to restore smooth, stable drawer movement and secure shelf alignment. Durable replacement designed to match the OEM fit and function for proper drawer operation. What it does:

• Supports and guides a refrigerator/freezer drawer or shelf for smooth in-and-out motion
• Restores proper alignment when drawers stick, drag, or sit unevenly
• Prevents drawers from falling out or binding during use
• Reduces noise caused by worn or damaged sliding tracks

• Always unplug the appliance or switch off power before servicing to avoid electrical hazard
• Remove the drawer or shelf to access mounting screws and clips before replacing the slide
• Compare the new slide to the original to ensure correct orientation and fastener locations
• Use common hand tools; do not force parts—if mounting holes don't line up, stop and verify part compatibility

This replacement deli drawer pan is for the fresh food compartment. It restores a smooth-sliding, dedicated space for meats and cheeses so the refrigerator stays organized and the drawer sits correctly on its tracks. What it does:

• Provides a dedicated bin for deli meats and cheeses in the fresh food section
• Seats on existing tracks under the shelf to slide in and out smoothly when undamaged
• Replacing a cracked, broken, or missing bin restores proper fit and containment
• Common symptoms: drawer cracked, won't stay on rails, difficult to slide, or missing

• Disconnect power and remove food from the area before servicing
• Pull the old drawer straight out and lift to clear the rails; align the new pan and slide it fully onto both tracks
• Handle the pan carefully—avoid flexing or forcing the plastic
• Remove the shelf above to gain clearance

This refrigerator water inlet tube routes water from the supply/valve into the appliance's water system. Replacing a cracked or kinked tube restores proper flow to the dispenser and ice maker while helping prevent leaks.

• Directs water from the inlet valve to internal components for dispensing and ice production
• Maintains a sealed, food-grade water path
• Replace if you notice leaks under/behind the unit, visible cracks/kinks, reduced or intermittent dispenser flow, or ice maker not filling
• Normal wear, brittleness, or damage during moves can lead to failures

• Disconnect power and shut off the water supply before servicing
• Place a towel or tray to catch residual water when disconnecting lines
• Note the original routing; release any retaining clips and disconnect the tube from fittings
• Route the new tube exactly like the original and fully seat tube ends in connectors; restore water and check for leaks

This replacement can dispenser fits inside the refrigerator door to hold and dispense canned beverages, restoring neat storage and easy single-can removal. Designed to match OEM fit and door-rack function for compatible models. What it does:

• Holds a stack of cans securely in the door to maximize shelf space
• Allows one-can-at-a-time dispensing for easier access and organization
• Prevents cans from rolling or shifting during door open/close
• Restores proper door storage if original dispenser is cracked, broken, or missing

• High-level installation: remove door shelf or trim as needed, unclip old dispenser, and snap new dispenser into place
• No special tools typically required; use a flat screwdriver or trim tool to release clips if needed
• Handle parts gently to avoid cracking the door trim; do not force clips
• Disconnect power only before working near electrical components

This water filter base secures the refrigerator's replaceable water filter cartridge and directs filtered water to the dispenser and icemaker. Replacing a damaged base restores a proper seal and helps prevent leaks and flow interruptions. What it does:

• Holds and seals the water filter cartridge so water passes through the filter media
• Directs filtered water to the dispenser and icemaker plumbing
• Prevents leaks caused by cracked or worn filter housing
• Can resolve low water flow, intermittent dispensing, or water taste issues when base is leaking or not sealing

• One water filter base assembly

• Turn off refrigerator and shut off the water supply before starting
• Relieve system pressure by dispensing water until flow stops, if applicable
• Remove the old housing carefully; inspect O-rings and replace if damaged
• Hand-tighten only; check connections and test for leaks after restoring water and power

This water filter cover encloses the refrigerator's filter housing for a clean look and protection. Replace a cracked, loose, or missing cover to restore a secure, smooth-opening access door for routine filter changes.

• Covers and protects the water filter in the fresh food compartment
• Opens to provide access when replacing the filter
• Helps prevent items from catching on the filter or housing
• Replace if the cover is cracked, the hinge or latch is broken, it won't stay closed, or it's missing

• Disconnect power and shut off the water supply before servicing
• Open the filter area and release the retaining tabs or hinge pins to remove the old cover
• Transfer any screws or hinge pieces from the original part if required
• Align and snap or secure the new cover; verify smooth opening and closing

This beam-style crisper cover is the glass shelf that sits above the crisper drawer, providing a flat support surface and helping contain spills while keeping produce organized. It restores the shelf surface and proper crisper function. What it does:

• Replaces a broken or missing crisper cover to restore a stable shelf over the crisper drawer
• Helps contain spills and prevents items from falling into the crisper
• Supports produce and other refrigerated items above the drawer area
• Works with the refrigerator's crisper beam/track system to maintain proper clearance and operation

• One crisper cover (beam-style) as shown

• Always unplug the refrigerator or shut off power before servicing interior components
• Remove food and any items from the shelf area before installation
• Handle the glass carefully; lift straight up/out from the tracks or supports and slide the replacement into position
• If the cover uses plastic clips or rails, inspect and replace damaged hardware to ensure a secure fit

This water filter housing is the refrigerator-mounted enclosure that holds and seals the replaceable water filter cartridge, helping ensure proper water flow to the dispenser and icemaker. Fits factory filter systems and restores secure filter seating. What it does:

• Houses and secures the refrigerator water filter cartridge to maintain a sealed water path
• Directs filtered water to the dispenser and icemaker while preventing leaks when installed correctly
• Can help stop water bypass or weak flow caused by damaged or cracked housings
• Supports proper alignment for O-rings and filter locking/engagement

• One water filter housing designed for the factory filter location

• Turn off the refrigerator water supply and dispense any residual water before servicing
• Remove power to the appliance if required by your model and follow manufacturer safety guidance
• Inspect and replace associated O-rings or seals if worn; confirm proper seating to prevent leaks

This refrigerator water filter mount secures the filter head/housing to the liner so the cartridge seats squarely and seals. Replace a cracked or loose mount to restore a snug fit and help prevent leaks or vibration.

• Holds the water filter housing firmly in place
• Aligns the cartridge for proper engagement with the filter head
• Helps maintain a watertight seal at the filter connection
• Common symptoms: filter won't lock in or sits crooked, drips around the filter area, difficulty installing/removing the filter, or rattling from a loose housing

• Disconnect power and shut off the water supply; dispense water to relieve line pressure
• Remove the filter and any cover/trim to access the mount; retain existing screws for reuse
• Install the new mount and tighten screws gently to avoid cracking plastic
• Reinstall the filter, restore water and power, flush the dispenser, and check for leaks

This replacement roller restores smooth sliding motion for a refrigerator drawer or bin along its track. Replacing a cracked or worn wheel helps prevent sticking, noise, and uneven movement that can strain rails and bins. What it does:

• Provides the rolling surface for a drawer, bin, or shelf track
• Restores smooth, consistent glide when opening or closing
• Helps reduce grinding/squeaking noises and binding
• Addresses issues like wobbling, tilting, or a missing/cracked wheel

• 1 roller

• Disconnect power before servicing
• Remove the drawer/bin to access the rail and roller
• Note the roller's orientation; transfer any reusable clips or fasteners
• Ensure the wheel spins freely and the drawer glides smoothly before reloading

This replacement screw fastens appliance components such as panels, brackets, and covers. Installing a new fastener restores a snug, rattle-free fit when the original screw is missing, stripped, or corroded.

• Secures covers, brackets, or trim to the cabinet or liner
• Replaces missing, stripped, or rusted hardware
• Helps reduce vibration and rattling from loose parts
• Supports proper alignment and stability of assemblies

• Disconnect power before servicing the appliance
• Use the correct driver/bit and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal
• Retain and reinstall any original washers or spacers, if present

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator clip is a small retainer that secures a component in place so it stays properly seated during use. Replacing a worn or missing clip restores a snug fit and helps eliminate looseness, rattling, or misalignment.

• Holds a part, panel, tube, or wire securely in its mounting point
• Maintains alignment to prevent shifting or vibration
• Helps preserve proper fit and airflow when components are correctly seated
• Symptoms can include loose or sagging pieces, rattling noises, or parts that won't stay attached

• Unplug the refrigerator; if working near water lines, shut off the water supply
• Note the clip's orientation before removal; take a photo for reference
• Use needle-nose pliers to release/install; avoid over-flexing the clip
• After installation, tug-test gently to confirm a secure fit before reassembling

This replacement screw secures appliance components to their mounting points so panels, brackets, and trim stay tight and aligned. Replace missing or stripped hardware to restore a solid, rattle-free fit and proper assembly integrity.

• Secures panels, brackets, and trim to prevent movement and maintain alignment
• Replaces missing, damaged, or stripped hardware that can compromise assembly
• Helps reduce rattling or vibration from loose components
• Restores proper fit after service or access panel removal

• Unplug the appliance before servicing; turn off water supply if working near dispenser/ice areas
• Compare the new screw to the original to ensure thread, head style, and length
• Start threading by hand to avoid cross-threading; tighten snugly without over-torquing, especially into plastic
• Retain and reuse any original washers, spacers, or clips as required

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head