Parts for Frigidaire FFHT2033VS4: Shelves Parts

Wire freezer shelf

This air diffuser kit replaces the vent/damper assembly that meters cold air from the freezer into the fresh-food section. It restores proper airflow and temperature balance when the original diffuser is stuck, broken, or leaking around the vent.

• Regulates and directs airflow from the freezer to the refrigerator compartment to maintain set temperatures
• Opens/closes the damper to reduce warm or cold spots in the fresh-food section
• Helps resolve symptoms such as a warm refrigerator with a normal freezer, weak airflow at the diffuser, temperature swings, or frost/condensation near the vent
• Replaces cracked housings, missing seals, or jammed/broken damper blades

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/covers to access the diffuser; note part orientation and screw locations
• Ensure all seals seat properly to prevent air leaks; do not overtighten plastic fasteners
• Restore power and allow up to 24 hours for temperatures to stabilize; adjust controls as needed

This refrigerator door gasket creates an airtight seal around the door to help keep cold air in and warm air out, preserving food freshness and helping the appliance run efficiently. What it does:

• Seals the door to maintain proper internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps reduce compressor runtime caused by air leaks
• Restores a tight magnetic seal for reliable door closure

• Disconnect power before starting any repair.
• Remove the old gasket and clean the gasket channel; install new gasket, aligning the magnetic edge and corners.
• Check for full compression around the door; adjust or reseat as needed for an even seal.
• Allow the gasket to settle and recheck after 24 hours; avoid using sharp tools that could damage the seal.

The Light Switch is an OEM replacement part for Frigidaire refrigerators. This switch controls the interior light of the refrigerator, turning it on when the door is opened and off when the door is closed. It ensures that the refrigerator is properly illuminated, making it easier to find items inside.

Causes of a bad light switch can include electrical malfunctions, physical damage from repeated use, or wear and tear over time.

Symptoms of a bad Light Switch include:

• Interior light not turning on when the door is opened
• Light flickering or intermittently turning on and off
• The refrigerator light staying on even when the door is closed

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Light Bulb is an OEM part for Frigidaire refrigerators. Located inside the fridge, it illuminates compartments for easy viewing of stored items.

Causes of bulb failure include the natural burnout period for incandescent and LED styles over extended use. Accidental breakage could occur during cleaning.

Symptoms of a bad light bulb include:

• Dark or completely unlit refrigerator sections  
• Warm bulb fixture indicating burnout
• Visible broken filament or cracked LED lens

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This refrigerator light socket holds and powers the interior bulb so you can clearly see inside. Replace a cracked, heat-damaged, or loose socket to restore reliable illumination when the interior light won't work or flickers.

• Provides the electrical connection and mounting point for the compartment light bulb
• Fixes symptoms such as no interior light with a known-good bulb
• Addresses intermittent flickering when the door is opened or closed
• Helps resolve visible charring, melting, or broken contacts on the socket
• Corrects a loose bulb that won't stay seated or lit

• Disconnect power to the refrigerator before servicing; remove the light lens/cover and bulb
• Note wire positions; release the old socket from its mount
• Transfer wires to the new socket one lead at a time and seat the socket fully
• Reinstall the bulb and cover; restore power and test
• Use only the bulb type and wattage specified for your model

This control box housing protects and secures the range/dryer/washer electronic control assembly, keeping wiring and the control board mounted and shielded from debris and heat. It restores a stable enclosure for reliable control operation. What it does:

• Provides a mounting enclosure for the appliance electronic control board and associated wiring harnesses
• Shields circuits from dust, moisture and incidental contact that can cause shorts or intermittent operation
• Keeps control components properly aligned so knobs, switches or displays sit correctly
• Helps prevent vibration-related loosening or damage to the control assembly
• Can eliminate symptoms like loose or rattling controls, exposed wiring, or intermittent control behavior when the housing is broken

• Disconnect power (unplug or turn off breaker) before any service to avoid shock or damage
• Handle the control board and ribbon cables carefully; transfer the PCB and fasteners from the old housing to the new housing if required
• Use the manufacturer-recommended screws/fasteners and correct alignment before restoring power

The Control Box Assembly is an OEM part for Frigidaire refrigerators. This complete assembly includes the electronic components and housing necessary to manage the refrigerator’s operations, such as temperature regulation, defrost cycles, and other vital functions.  

Causes of a bad control box assembly can include electrical surges, moisture damage, or normal wear and tear over time. Additionally, physical damage or faults in the wiring can lead to control box failure.

Symptoms of a bad control box assembly include:

• The refrigerator not cooling properly
• Error codes displayed on the control panel
• Inconsistent or fluctuating temperatures
• The refrigerator or freezer not defrosting as needed
• Unresponsive control buttons

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Shelf - "Spill-Safe" is an OEM part for Frigidaire refrigerators. This shelf is designed to contain spills and prevent liquids from leaking onto other shelves or the bottom of the refrigerator, helping to maintain cleanliness and order within the appliance.

Over time, heavy loads, accidental impacts, or temperature fluctuations can cause the shelf to weaken or break.

Symptoms of a bad shelf include:

• Visible cracks or breaks in the shelf
• Liquids leaking through the shelf
• Difficulty in fitting the shelf securely in place
• The shelf not supporting weight properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Shelf - "Spill-Safe" is an OEM part for Frigidaire refrigerators. This shelf is designed to contain spills and prevent liquids from leaking onto other shelves or the bottom of the refrigerator, helping to maintain cleanliness and order within the appliance.

Over time, heavy loads, accidental impacts, or temperature fluctuations can cause the shelf to weaken or break.

Symptoms of a bad shelf include:

• Visible cracks or breaks in the shelf
• Liquids leaking through the shelf
• Difficulty in fitting the shelf securely in place
• The shelf not supporting weight properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Humidity Control Slide is an OEM part for Frigidaire refrigerators. This part regulates the humidity levels within the crisper drawers, helping to keep fruits and vegetables fresh for longer periods. The slide allows users to adjust the ventilation in the crisper, providing optimal storage conditions for different types of produce.

Causes of a bad humidity control slide can include regular wear and tear, accidental breakage, or misalignment that prevents it from moving smoothly.

Symptoms of a bad humidity control slide include:

• Difficulty adjusting the humidity settings
• The slide feeling loose or falling off
• Produce not staying fresh as long as expected
• Visible damage or cracks on the slide mechanism

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Frigidaire humidity control slide is an OEM replacement part responsible for regulating and adjusting the humidity levels within the crisper drawers of a refrigerator. This slide is found on the fresh food drawer to allow adjustment of the amount of moisture retained in the crisper drawers, which is essential for preserving the freshness and crispness of fruits and vegetables.

By adjusting the humidity control slide, users can create an ideal environment for different types of produce, ensuring that they stay fresh for longer periods and preventing food waste from wilting or drying out prematurely.

This part fixes the following symptoms

• Inability to adjust or control the humidity levels within the crisper drawers.
• Produce items wilting or drying out quickly due to improper humidity regulation.
• The control slide becoming loose, stuck, or difficult to move.

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

The Crisper Pan Cover is an OEM part for Frigidaire refrigerators. It serves as the shelf that sits above the crisper drawers and supports various items while providing a lid to help maintain the humidity levels necessary to keep fruits and vegetables fresh longer. This cover typically is only the frame and does not include the glass.

Symptoms of a bad Crisper Pan Cover include:

• Cracks or damage to the cover that can compromise its structural integrity
• Warping or bending that affects the fit and function
• Difficulty sliding or fitting the cover properly over the crisper drawers

Causes of a bad crisper pan cover can include overloading the shelf with too much weight, impacts from dropping heavy items, or thermal stress from fluctuations in refrigerator temperatures.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Crisper Pan is an OEM part for Frigidaire refrigerators. The crisper pan measures approximately 19" x 7 1/2" x 11 1/2" It is responsible for lining the bottom of the refrigerator's vegetable and fruit crisper drawers, where perishable items like produce are stored. The crisper pan helps extend the shelf life of fruits and vegetables.

Causes of a bad crisper pan can include heavy impact from dropping, regular wear and tear, or exposure to harsh cleaning chemicals.

Symptoms of a bad crisper pan include:

• Cracks or splits in the plastic
• Difficulty sliding the pan in and out of its compartment
• Food not staying as fresh due to improper humidity levels
• Accumulation of dirt and stains that are hard to clean

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Meat Pan is an OEM part for Frigidaire refrigerators. This drawer is specifically designed to store meats and other perishables at an optimal temperature within your refrigerator. Its placement often allows for slightly different temperature conditions than the rest of the refrigerator, helping to keep meats fresher for longer. This bin measures approximately 18 inches long and 13 inches wide,

Symptoms of a failing meat pan include:

• Cracks or breaks in the pan that compromise its structural integrity
• Difficulty sliding the pan in and out due to damage or warping
• The pan not sealing properly, which can affect temperature regulation within the compartment

Causes of meat pan damage usually stem from overloading the drawer beyond its capacity, frequent and forceful use, or accidental damage from items being dropped on or in it.

This OEM part is compatible with Kenmore, Frigidaire, Crosley, Westinghouse, Electrolux, Kelvinator, and Gibson brands.

The Pan Cover Glass Insert is an OEM part for Frigidaire refrigerators. It acts as the shelf above the crisper drawers, providing a stable and transparent surface for storing fruits, vegetables, and other perishables. This glass insert is crucial for maintaining the organization within the fridge, allowing for easy visibility and access to items stored in the crisper drawers beneath it. 

Causes of damage to the Pan Cover Glass Insert can include overloading it with too heavy items, accidental impacts during the loading or unloading of groceries, or sudden temperature changes that can cause glass to weaken or crack.

Symptoms indicating the need for a replacement include:

• Visible cracks or chips in the glass
• Scratches that impair visibility
• Shattering of the glass insert

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator shelf spacer positions and supports a shelf so it sits secure and level. Replacing a worn or missing spacer helps eliminate wobble or shifting and restores proper fit and alignment inside the compartment. What it does

• Maintains correct spacing and alignment for the shelf
• Helps keep the shelf level and secure in its track or frame
• Replaces cracked, deformed, or missing spacers
• Symptoms can include a loose, tilted, or rattling shelf, or visible gaps where the shelf should seat

• One shelf spacer

• Disconnect power to the refrigerator before servicing
• Remove the shelf to access the spacer location
• Gently pry out the old spacer; avoid stressing plastic or glass components
• Press the new spacer firmly into place and reinstall the shelf, ensuring proper orientation