Parts for Frigidaire FFTR2028SS3A: 04 - Shelves Parts

Wire freezer shelf

This air diffuser kit replaces the vent/damper assembly that meters cold air from the freezer into the fresh-food section. It restores proper airflow and temperature balance when the original diffuser is stuck, broken, or leaking around the vent.

• Regulates and directs airflow from the freezer to the refrigerator compartment to maintain set temperatures
• Opens/closes the damper to reduce warm or cold spots in the fresh-food section
• Helps resolve symptoms such as a warm refrigerator with a normal freezer, weak airflow at the diffuser, temperature swings, or frost/condensation near the vent
• Replaces cracked housings, missing seals, or jammed/broken damper blades

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/covers to access the diffuser; note part orientation and screw locations
• Ensure all seals seat properly to prevent air leaks; do not overtighten plastic fasteners
• Restore power and allow up to 24 hours for temperatures to stabilize; adjust controls as needed

This refrigerator door gasket creates an airtight seal around the door to help keep cold air in and warm air out, preserving food freshness and helping the appliance run efficiently. What it does:

• Seals the door to maintain proper internal temperature
• Reduces frost and moisture buildup by preventing warm, humid air from entering
• Helps reduce compressor runtime caused by air leaks
• Restores a tight magnetic seal for reliable door closure

• Disconnect power before starting any repair.
• Remove the old gasket and clean the gasket channel; install new gasket, aligning the magnetic edge and corners.
• Check for full compression around the door; adjust or reseat as needed for an even seal.
• Allow the gasket to settle and recheck after 24 hours; avoid using sharp tools that could damage the seal.

The Light Switch is an OEM replacement part for Frigidaire refrigerators. This switch controls the interior light of the refrigerator, turning it on when the door is opened and off when the door is closed. It ensures that the refrigerator is properly illuminated, making it easier to find items inside.

Causes of a bad light switch can include electrical malfunctions, physical damage from repeated use, or wear and tear over time.

Symptoms of a bad Light Switch include:

• Interior light not turning on when the door is opened
• Light flickering or intermittently turning on and off
• The refrigerator light staying on even when the door is closed

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Light Bulb is an OEM part for Frigidaire refrigerators. Located inside the fridge, it illuminates compartments for easy viewing of stored items.

Causes of bulb failure include the natural burnout period for incandescent and LED styles over extended use. Accidental breakage could occur during cleaning.

Symptoms of a bad light bulb include:

• Dark or completely unlit refrigerator sections  
• Warm bulb fixture indicating burnout
• Visible broken filament or cracked LED lens

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replacement air purifier assembly that restores the refrigerator's internal air-care function and helps reduce persistent odors. Installs in the fresh-food compartment to restore the appliance's odor-control and air-freshening performance. What it does:

• Houses the refrigerator's air-purifying module to help trap and reduce odors and airborne contaminants.
• Restores air-care performance when the original purifier is damaged, clogged, or missing.
• Works as part of the fridge's internal air circulation and odor-control system.

• One air purifier assembly

• Disconnect power to the appliance before accessing internal panels or components.
• Remove interior panels or shelves as required to reach the purifier; keep parts and fasteners organized.
• Handle the assembly carefully to avoid damage; use basic hand tools.

The Temperature Sensor (10K NTC) is an OEM replacement part for Frigidaire refrigerators. This sensor monitors the internal temperature of the refrigerator or freezer compartment, sending signals to the control board to regulate cooling cycles. It ensures the appliance maintains the correct temperature for optimal food preservation.

Temperature sensors can fail due to wear over time, electrical issues, or exposure to moisture. A malfunctioning sensor can cause inaccurate temperature readings, leading to improper cooling or freezing.

Symptoms of a bad temperature sensor include:

• Fluctuating or incorrect temperatures in the refrigerator or freezer
• Food spoiling faster than expected or freezing inappropriately
• Error codes related to temperature regulation
• The refrigerator running continuously or cycling too often

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This model-specific refrigerator cover encloses and protects a designated interior area or component. Replacing a cracked, loose, or missing cover restores proper fit and finish and helps maintain intended airflow and safe operation inside the cabinet. What it does

• Shields and encloses the specified compartment to protect internal components from debris and damage
• Helps maintain designed airflow and temperature by properly closing the opening
• Restores a clean, finished look and prevents items from snagging or falling into moving parts
• Common symptoms: cracked or broken cover, loose fit or rattling, visible gaps, or the cover will not stay attached

• 1 cover

• Disconnect power and remove items, shelves, or bins as needed to access the area
• Note fastener type and locations; retain and reuse original hardware
• Align tabs/guides, seat the cover fully, then secure without overtightening
• Restore power and confirm the cover is secure and clear of any fan or moving parts

The Shelf - "Spill-Safe" is an OEM part for Frigidaire refrigerators. This shelf is designed to contain spills and prevent liquids from leaking onto other shelves or the bottom of the refrigerator, helping to maintain cleanliness and order within the appliance.

Over time, heavy loads, accidental impacts, or temperature fluctuations can cause the shelf to weaken or break.

Symptoms of a bad shelf include:

• Visible cracks or breaks in the shelf
• Liquids leaking through the shelf
• Difficulty in fitting the shelf securely in place
• The shelf not supporting weight properly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Crisper Pan Cover is an OEM part for Frigidaire refrigerators. It serves as the shelf that sits above the crisper drawers and supports various items while providing a lid to help maintain the humidity levels necessary to keep fruits and vegetables fresh longer. This cover typically is only the frame and does not include the glass.

Symptoms of a bad Crisper Pan Cover include:

• Cracks or damage to the cover that can compromise its structural integrity
• Warping or bending that affects the fit and function
• Difficulty sliding or fitting the cover properly over the crisper drawers

Causes of a bad crisper pan cover can include overloading the shelf with too much weight, impacts from dropping heavy items, or thermal stress from fluctuations in refrigerator temperatures.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This refrigerator drawer pan replaces a broken or missing bin in the fresh food section. Restore organized storage and smooth sliding access so produce and snacks stay contained and easy to reach.

• Holds and organizes items in the refrigerator's fresh food compartment
• Helps contain drips and spills to keep shelves cleaner
• Slides on existing tracks for easy access
• Replace when cracked, warped, or the front/lip is broken, or the drawer sticks, falls, or is missing

• Remove contents; pull the old drawer straight out to clear the tracks or stops
• Align the new pan with the same tracks and slide it in until fully seated
• Do not force into place; handle carefully to avoid cracking

This slide is the track/rail that supports and guides a compatible refrigerator drawer, bin, or basket. Replacing a worn slide restores smooth, even movement so the drawer opens and closes properly without binding or popping off its track.

• Guides and supports a drawer/bin for smooth travel inside the refrigerator
• Common fix for drawers that stick, jam, feel rough, or fall off the track
• Helps keep the drawer aligned and level in its compartment
• Replace if the rail is cracked, warped, or excessively worn

• Disconnect power and remove food/items from the affected area before servicing.
• Remove the drawer and any cover/shelf as needed; retain and reuse existing screws/clips.
• Install the new slide in the same position, then test drawer movement before restoring power.

This meat pan is the replacement deli-style tray used inside the refrigerator to hold meats, cheeses and other deli items. It restores proper storage and organization for the deli/drawer area. What it does:

• Provides a flat, food-safe surface for storing deli meats, cheeses and prepared foods
• Keeps items contained to reduce spills and cross-contamination inside the deli/drawer area
• Replaces a cracked, warped or missing deli/meat tray to restore usable storage
• Fits into the fridge's deli/drawer track or shelf area to align with the existing drawer

• One meat pan/deli tray (single replacement)

• Remove food items and the deli drawer before installing the new pan
• Slide the pan into the existing drawer tracks or set it into the shelf support as originally positioned
• Hand-wash with mild detergent; avoid abrasive cleaners or scouring pads that can damage the surface

This clip mounts to the refrigerator liner and secures the crisper cover/slide rail so the drawer stays supported and glides properly. Replace a broken or missing clip to restore alignment and smooth operation of the crisper.

• Holds the crisper cover/slide rail firmly against the cabinet liner
• Supports the crisper drawer to prevent sagging or tilt
• Helps restore smooth opening and closing of the crisper drawer
• Common symptoms of failure: loose rail, drawer off-track, difficulty sliding, or a cracked/missing clip

• Unplug the refrigerator or disconnect power before servicing
• Remove the crisper drawer and cover/glass to access the clip
• Release the old clip (snap tabs or screw), align and secure the new clip; reuse the original fastener if your model uses one
• Reinstall the cover and drawer; the drawer slides freely

The Pan Cover Glass Insert is an OEM part for Frigidaire refrigerators. It acts as the shelf above the crisper drawers, providing a stable and transparent surface for storing fruits, vegetables, and other perishables. This glass insert is crucial for maintaining the organization within the fridge, allowing for easy visibility and access to items stored in the crisper drawers beneath it. 

Causes of damage to the Pan Cover Glass Insert can include overloading it with too heavy items, accidental impacts during the loading or unloading of groceries, or sudden temperature changes that can cause glass to weaken or crack.

Symptoms indicating the need for a replacement include:

• Visible cracks or chips in the glass
• Scratches that impair visibility
• Shattering of the glass insert

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This factory fastener secures appliance panels and components. Replace a missing, stripped, or corroded screw to restore a tight, rattle-free fit and keep brackets and covers properly aligned.

• Fastens panels, brackets, and internal parts as specified by the manufacturer
• Helps maintain alignment and reduces vibration/rattling
• Replace if the head is stripped, threads are damaged, or corrosion is present
• Symptoms include loose/missing hardware, gaps, or rattling during operation

• Disconnect power; shut off gas/water if applicable before servicing
• Use the correct driver/bit size to avoid stripping the head
• Start threads by hand to prevent cross-threading; do not overtighten
• Match screw length/thread to the location; replace in sets when required

This refrigerator shelf spacer positions and supports a shelf so it sits secure and level. Replacing a worn or missing spacer helps eliminate wobble or shifting and restores proper fit and alignment inside the compartment. What it does

• Maintains correct spacing and alignment for the shelf
• Helps keep the shelf level and secure in its track or frame
• Replaces cracked, deformed, or missing spacers
• Symptoms can include a loose, tilted, or rattling shelf, or visible gaps where the shelf should seat

• One shelf spacer

• Disconnect power to the refrigerator before servicing
• Remove the shelf to access the spacer location
• Gently pry out the old spacer; avoid stressing plastic or glass components
• Press the new spacer firmly into place and reinstall the shelf, ensuring proper orientation

This support beam is the structural rail that supports a refrigerator shelf and its pantry/drawer assembly. Replace a cracked or missing beam to restore level support, prevent sagging, and keep drawers operating smoothly.

• Spans the compartment to support the shelf/pantry frame and distribute weight
• Keeps the shelf level and stable under load
• Helps maintain proper alignment for attached drawers or bins
• Common symptoms: shelf tilts or sags; drawers bind, scrape, or drop
• Visible cracks, broken tabs, or a missing beam

• Disconnect power before servicing
• Remove food items, the shelf/frame, and any drawers or bins supported by the beam
• Release the beam from locking tabs or fasteners and remove the old part
• Seat the new beam fully in the mounting points, then reinstall the shelf and drawers and check for level

This small clip secures the crisper cover's slide so it stays aligned and operates smoothly. Replacing a broken or missing clip restores proper slide action and helps keep your crisper cover assembly functioning as designed.

• Holds the crisper cover slide in place and aligned with its track
• Helps the slide move smoothly without popping off or binding
• Common symptoms: slide is loose or falls out, won't stay in place, cracked/missing clip
• Visual damage or loss can leave the crisper drawer cover slide inoperable

• Disconnect power and remove food items for safe access
• Remove the crisper drawer and lift out the crisper cover assembly
• Release the damaged clip and snap the new clip into the cover/slide as oriented
• Reassemble and verify the slide moves freely end to end