Parts for Ge C2Y486SDL1SS: Small Door Assembly Parts

This small set screw secures components inside your refrigerator. Replacing a missing or stripped set screw restores a tight, reliable hold so attached parts stay aligned and are less likely to loosen or rattle during use.

• Fastens an attached part to its mounting point to prevent movement or slipping
• Helps maintain proper alignment of handles, brackets, or trim pieces
• Reduces wobble, vibration, and rattling noises caused by loose hardware
• Replaces missing, stripped, or corroded set screws

• Unplug the refrigerator and shut off water if working near door/dispenser areas
• Support the part being secured; start the screw by hand to avoid cross-threading
• Tighten with the correct driver for your model; do not overtighten to prevent stripping
• The component is secure and aligned before restoring power

This small end cap fits the end of an extension piece to act as a stop and finish. It restores a secure, finished edge so the sliding component or trim stays aligned and doesn't over-travel during use.

• Caps the end of an extension rail or trim to prevent over-travel and pullout
• Keeps the assembly aligned to reduce wobble
• Replaces cracked, missing, or worn caps
• Helps eliminate rattling and exposed edges

• Disconnect power and allow all hot surfaces to cool before servicing
• Access the end of the extension/rail; release any locking tab and remove the old cap
• Align and snap or press the new cap into place
• Verify smooth travel and a secure stop after installation

A 12" replacement glass door that restores a clear viewing window for your appliance and helps contain heat. Designed as a direct-fit OEM replacement to maintain original appearance and function. What it does:

• Replaces damaged, cracked or cloudy door glass to restore safe, visible operation
• Helps contain heat and splatter inside the appliance for efficient cooking/operation
• Restores the appliance's original look when the existing glass is scratched or discolored
• Reduces drafts and maintains proper door seal performance when glass is intact

• Handle with care; glass can chip or break—wear cut-resistant gloves and eye protection
• Follow the appliance manufacturer's disassembly/reassembly instructions
• Do not overtighten hardware when reinstalling; use original screws and clips if available

This 12" door gasket seals the oven/range door to help maintain proper cooking temperature and prevent heat and fumes from escaping. Replacing a worn gasket restores a tighter seal for safer, more efficient operation. What it does:

• Creates a heat-tight seal around the oven/range door to help retain temperature
• Reduces heat loss and prevents smoke or fumes from leaking into the kitchen
• Helps the appliance maintain consistent cooking or baking performance
• Commonly replaced when the gasket is cracked, torn, flattened, or shows visible gaps

• One (1) door gasket (12")

• Disconnect power to the appliance and allow the oven to fully cool before beginning
• Remove the old gasket by pulling it out of the retainer channel; inspect the channel for debris
• Press the new gasket into the channel evenly, working around the door so it seats fully without twisting

This endcap replaces a damaged or missing door-handle end piece to restore the handle's finished look and protect exposed edges. It fits on the end of the appliance door handle to conceal hardware and improve grip. What it does:

• Covers the exposed end of a door handle for a clean, finished appearance
• Helps protect fingers from sharp edges and hides mounting screws
• Keeps the handle secure by retaining the handle trim in place
• Common symptom: cracked, broken or missing endcap that leaves fasteners exposed

• One endcap (handle) as shown

• Turn off power to affected appliance and work on a cool, empty door before starting
• Removal typically requires loosening the handle set screws or removing trim pieces; keep small fasteners in a safe place
• Align the endcap over the handle end and snap or fasten per the factory method; avoid forcing parts to prevent breakage

This oven door glass inner panel restores the viewing window and helps contain heat for efficient cooking. Replaces a cracked, scratched or broken inner door glass to improve visibility and maintain oven performance. What it does:

• Replaces damaged or shattered inner oven door glass to restore a clear viewing window
• Helps maintain proper heat containment for consistent cooking results
• Reduces drafts and heat loss from a compromised door assembly
• Improves safety by replacing cracked or weakened glass

• Disconnect power (and gas, if applicable) and allow the appliance to fully cool before starting
• Wear cut-resistant gloves and eye protection when handling glass
• Remove the door to access the inner panel; follow OEM steps for reassembly
• Inspect door clips, gaskets and fasteners during install; replace any damaged hardware

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold