Need Help?
Call or text
The Flame Sensor is an OEM replacement part for Whirlpool gas dryers. This component plays a critical safety role by monitoring the presence of the gas burner flame during the drying cycle.
Causes of needing to replace the flame sensor can incl
I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more
Traps lint and debris during drying cycles to prevent exhaust clogs and maintain efficiency. Replace when torn, damaged, or not catching lint properly.
This was a Maytag DE312 actually a Whirlpool labeled as Maytag) and is 27 years old. Replaced motor, drive belt and drum rollers. One tricky part was the motor because the new motor comes with integral starter and it was necessary to cut off existing female spade connectors on some wires and crimp on new connectors. Instructions were adequate but need to be carefully followed and a decent electrical stripping and crimping tool must be at hand. I bought a new motor drive pulley because another... Read more
The Cycling Thermostat is an OEM part for Whirlpool dryers. It regulates and monitors the temperature inside the dryer during the drying cycle. It ensures that the dryer doesn't overheat and prevents potential damage to clothes or the dryer it
This Maytag dryer was bought in 1985 if memory serves. It has worked hard with few repairs done by yours truly over the years. Thanks to the engineering and excellent design by Maytag staff, removing parts are relatively easy. Once I opened the unit, I found it to be full of lint. I cleaned the entire inside and the vent pipe duct work. I found the blower wheel assembly worn. Though it was not cause of my problem, I decided to change it along with the igniter, heater relay and the fan belt. I... Read more
The LP Gas Conversion Kit is an OEM part for Whirlpool appliances. This kit allows for the conversion of natural gas appliances to use liquid propane (LP) gas. It includes all necessary components, such as orifices and instructions, to ensure a safe an
The kit was very simple it took longer to take the dryer apart than it did to do the change over and it works great thank you for you're product Read more
Replace a cracked, clogged, or worn burner head on your gas cooktop. This component directs gas through flame ports for even heating and reliable ignition.
I ordered replacement parts to convert the side to individual burners. Read more
This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does
Replaced the hose Read more
Tubeless air valve for lawn tractor and mower tires. Replace when cracked, leaking, or damaged during tire changes. Installs in wheel rim for proper inflation.
Shear pin kit for lawn tractor drive systems. Replaces broken or sheared pins that protect drivetrain components. Includes hardware for installation.
Fuel pickup filter draws gas from tank to carburetor. Replace if engine won't start or runs poorly due to clogged filter. Verify fit with your model number.
Usually ships within 4 - 14 days
This timer knob replaces a worn or broken range timer control knob, restoring a positive grip and reliable dial operation so you can set cooking times accurately. Easy-restore part for common knob damage or wear. What it does:
Seals the carburetor adapter to prevent dirt and debris from entering your chainsaw engine. Replace if cracked, brittle, or leaking. Confirm fit by model.
This ball bearing and seal are used in a range of chainsaw models. It acts as part of the blade assembly and is designed to both lessen friction and stabilize moving parts. This bearing is also set within a race and the entire race/bearing/seal assembly m
Chain overheating or not staying oiled? This oil pump kit delivers consistent lubrication to prevent chain damage and ensure safe operation. DIY fix.
Secures the muffler cover to the muffler on chainsaws and small engines. Replace if screw is stripped, missing, or no longer holds the cover securely.
Replacement edger blade for lawn edgers that trim grass along sidewalks and driveways. Replace if blade is bent, chipped, or worn from pavement contact.