Parts for Frigidaire FFHT1835VB1: System Parts

Replace your refrigerator's water line tube if cracked, kinked, or leaking. This tube connects the water supply to the dispenser or ice maker assembly.

Secures wire harnesses and ground wires to your refrigerator cabinet. Replace if broken or missing to prevent wire damage. Verify fit with your model.

Fixes poor cooling and warm temps caused by moisture in the sealed system. This filter-drier protects the compressor during refrigerant repairs.

Refrigerator not cooling properly or running constantly? This condenser coil assembly removes heat from refrigerant to restore efficient cooling performance.

Wire harness connects electronic components inside your refrigerator. Replace if wires are damaged, frayed, connectors are broken, or harness is missing.

Freezer overheating or food freezing in fridge? This thermistor sensor monitors temperature to regulate cooling. Check resistance (5K ohms at room temp).

If your refrigerator won't cool or stays too warm, the main control board may have failed. This board controls the compressor, fans, and defrost cycle.

Fix a refrigerator that won't cool or has a compressor that clicks but won't start with this compressor starter. Simple electrical repair for DIYers.

Replacement cover that protects internal components in your refrigerator. Installs where the original was cracked, broken, or missing to shield parts.

This rubber grommet cushions and protects wiring, tubing or mounting points to reduce vibration and prevent chafing. It restores a tighter fit where the original grommet has worn, torn or become brittle. What it does:

• Cushions and isolates wiring, hoses, or mounting studs to reduce vibration and noise
• Prevents chafing and abrasion where components pass through metal or plastic openings
• Helps maintain proper alignment and fit of panels or assemblies
• Common symptom: visible wear, cracking, a loose or rattling component near the grommet location

• One grommet

• Disconnect power and water before servicing the appliance
• Inspect surrounding components for damage and replace any additional worn seals
• Gently press the grommet into place; small hand tools or a blunt plastic driver may help
• If routing wires or hoses, ensure they sit fully inside the grommet to prevent chafing

Molded cabinet base that supports lower refrigerator components and directs condensation to the drain. Replace if cracked, broken, or damaged to restore stability.

Fix a refrigerator that won't start or run properly with this compressor capacitor. Located near the compressor, this electrical component helps start the motor.

Replacement condensate drain tube for top-mount refrigerators. Routes water away from components to prevent leaks or pooling. Needed when original tube is damaged, cracked, or clogged.

Water pooling under your refrigerator? This drip pan collects defrost water and condensation to prevent leaks. Direct-fit replacement part. Easy DIY.

Refrigerator not cooling or compressor won't start? This electronic start device helps the compressor start reliably to restore normal cooling performance.

Fix a warm freezer or noisy cooling with this evaporator fan assembly. Restores airflow across the coils to maintain even temperatures in your fridge.

Fix excessive frost buildup on evaporator coils with this defrost heater assembly. Solves cooling cycles and thawing issues in top-mount refrigerators.

This support mounting bracket secures and steadies a key appliance component, helping maintain proper alignment and reliable operation. It's a direct-fit replacement designed to restore part stability and reduce movement-related issues. What it does:

• Provides structural support and alignment for the associated assembly
• Helps prevent sagging, misalignment, or excessive vibration of the component
• Restores reliable mounting after a cracked, bent, or missing support
• Supports normal operation by keeping parts correctly positioned

• One support mounting bracket

• Install with factory-recommended fasteners; inspect surrounding parts for wear before reassembly
• Use basic hand tools; avoid overtightening fasteners which can deform the part
• Disconnect power to the appliance if required to access the mounting area

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Replacement mounting screw for refrigerators and freezers. Secures panels, brackets, trim, and covers. Replace if missing, stripped, or damaged.

Mounting screw for refrigerators and freezers. Secures panels, brackets, and internal components. Replace when stripped, missing, or damaged.