Thermador Range / Cooktop / Oven Parts

Replacement potentiometer that restores precise control of appliance settings by regulating resistance in the control circuit. Use it when a rotary control is unresponsive or produces inconsistent settings for reliable operation. What it does:

• Varies electrical resistance to adjust settings controlled by the knob (e.g., temperature, speed, or level)
• Replaces a worn or faulty rotary control that causes unresponsive or erratic behavior
• Helps restore smooth, predictable adjustment when the original control no longer responds properly
• Fits into the existing control assembly to restore user input accuracy

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access the control panel or module to remove the old potentiometer; note knob/shaft orientation and wiring
• Match wire connections and mounting position of the replacement part; test operation before reassembling the panel

This jet holder assembly secures the burner orifice and delivers the correct-sized gas jet for a 12,500 BTU natural gas burner, helping restore proper flame size and consistent ignition. What it does:

• Holds the burner orifice in the correct position so gas flows through the proper jet
• Provides the factory-sized orifice for a 12,500 BTU natural gas burner to maintain intended flame height
• Helps correct weak or uneven flames caused by a missing, damaged, or incorrect jet holder
• Supports reliable ignition when installed and aligned properly

• One jet holder assembly (blue) with the 12,500 BTU natural gas orifice installed

• Turn off the appliance and shut off the gas supply before starting any work
• Only install the exact orifice variant specified for your appliance; confirm color/marking and orientation before tightening
• Re-check all gas fittings and perform a leak test after installation

This deflector directs dishwasher spray water for proper coverage and helps protect nearby components from direct spray. It replaces broken or warped deflectors to restore intended water flow and cleaning performance. What it does

• Guides spray water toward dishes and spray arms to maintain even coverage
• Prevents direct spray from hitting sensitive components or seals
• Helps reduce spotting and uneven cleaning caused by misdirected water
• Fits where the original deflector is mounted; replaces cracked, broken, or deformed pieces

• Turn off power and water supply to the appliance before starting any repair
• Remove the lower rack or other obstructions for clear access to the mounting area
• Inspect mounting tabs and surrounding components; replace any damaged clips or fasteners

The Surface Element (240V-2100W) is an OEM part for Bosch cooktops and ranges. It provides consistent, even heating from below pans on the cooktop surface.

Causes of a bad surface element can include normal wear and damage from extended, heavy usage. Food or liquid spills left on the element for prolonged periods could potentially corrode the coils or electronics over time as well.

Symptoms of a bad surface element include:

• Element not heating up at all or heating unevenly
• Element heating intermittently or stopping prematurely
• Buzzing, clicking or smoke coming from below the element
• Tripped or blown circuit breakers when using that element

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This burner base supports the cooktop's burner cap and directs flame for even heating. It replaces a damaged or warped base to restore stable burner alignment and consistent flame pattern. What it does:

• Holds the burner cap in place and centers the gas flame
• Channels gas flow for proper burner operation
• Helps prevent wobbling or uneven heating from a warped base
• Commonly replaced when the base is cracked, corroded, or bent

• One burner base (B)

• Turn off gas supply and power to the appliance before servicing
• Remove surrounding burner components and reassemble in reverse order
• Inspect nearby seals and burner ports for damage; replace if necessary

This burner cap assembly covers and protects the gas burner head and helps shape the flame for even cooking. It replaces a damaged or missing cap to restore proper burner appearance and flame pattern on compatible cooktops. What it does:

• Centers and shields the burner head to promote an even flame distribution during use
• Replaces cracked, warped, or missing caps that can cause uneven heating or unstable flames
• Helps maintain correct burner alignment for reliable ignition
• Restores finished appearance around the burner for safe, proper operation

• One black burner cap assembly

• Turn off gas supply and power to the appliance before servicing
• Allow the cooktop to cool fully; handle with care to avoid scratching or chipping
• Seat the cap squarely on the burner head—no tools typically required

Replacement incandescent interior oven lamp that restores cooking-cavity illumination so you can check food without opening the door. Direct-fit replacement sold individually for compatible appliances. What it does:

• Restores interior oven lighting so you can monitor cooking without opening the door
• Replaces a burned-out or flickering bulb to eliminate dark or partially lit oven interiors
• Helps diagnose whether lack of light is due to the bulb
• Fits behind the oven light cover and provides general illumination of the cavity

• Turn off power and allow the oven to cool completely before replacing the lamp
• Remove the oven light cover or shield per your appliance instructions before swapping the bulb
• Avoid touching the glass with bare hands; use a clean cloth or gloves to prevent oils on the bulb
• Reinstall the cover securely and test the lamp; if it still does not light, check the fixture and power

A replacement glass turntable plate that restores a microwave's rotating cooking surface for even heating and stable cookware support. Fits on the drive roller to provide a flat, heat-safe surface for daily microwave use. What it does:

• Replaces a cracked, chipped or missing glass turntable so food heats more evenly
• Provides a stable surface for plates and bowls to rotate during cooking
• Works with the turntable roller and coupling to restore proper rotation
• Prevents wobble and scraping that can occur with damaged glass

• Unplug the microwave or disconnect power before installing
• Handle the glass carefully to avoid cuts; do not install if chipped or cracked
• Align plate on the center drive coupling/roller support; it seats and rotates freely
• Use only the exact OEM plate size and part number to ensure proper fit

This air interlock is the airflow switch that helps monitor and control dryer vent airflow, ensuring the appliance only runs when proper air movement is detected. It replaces a worn or failed interlock to restore normal vent sensing. What it does:

• Senses airflow through the vent and signals the control system to allow or stop operation
• Prevents dryer from starting or continuing a cycle when airflow is restricted
• Common symptom: dryer fails to start, stops mid-cycle, or shows poor drying performance
• Can help address intermittent operation caused by a faulty vent sensing switch

• Disconnect power before servicing to avoid electrical shock
• Handle the switch and wiring gently; verify connector orientation before reinstalling
• Confirm venting is clear and intact when replacing this part

This 1/4" gas supply tubing connects the appliance's gas line to the valve, providing a secure path for fuel so the unit can ignite and operate safely. Use when tubing is damaged, leaking, or replaced during valve service. What it does:

• Channels natural gas/LP from the household supply to the appliance valve
• Replaces cracked, corroded, or bent tubing that can cause leaks
• Helps stop symptoms like a persistent gas smell, failure to ignite, or intermittent burner operation
• Works with the appliance's inlet and control valve fittings to maintain proper gas flow

• Turn off the gas supply and electrical power before starting work
• Use approved fittings, thread sealant rated for gas, and test all connections for leaks after installation
• Do not modify or reuse damaged tubing; replace with exact-fit parts

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

This control knob replaces a worn, broken, or missing stove/oven knob to restore safe, reliable control and improve the appliance's appearance. It fits directly onto the control shaft for a secure, tactile grip. What it does

• Replaces a damaged or missing control knob so you can set burners or oven functions accurately
• Provides a solid grip and clear pointer for selecting settings
• Stops slipping or spinning caused by a cracked or worn knob
• Helps restore normal operation when the original knob is loose or won't stay engaged

• Disconnect power (unplug appliance or switch off breaker) before servicing to avoid electrical or burn hazards.
• Pull the old knob straight off the control shaft; no special tools typically required.
• Align the new knob's splines with the shaft and push straight on until fully seated.
• Do not force the knob; if it does not fit, check shaft shape and orientation before applying pressure.

A replacement spring hinge that helps support and counterbalance the appliance door for smooth opening and closing and proper alignment. Restores reliable door movement and reduces drop or slamming when the original spring is worn or broken. What it does:

• Provides counterbalance tension to help hold the door open and control closing motion
• Restores proper door alignment and prevents uneven closing or gaps
• Reduces sudden drops, slamming, or heavy-feeling doors caused by a weak or broken spring
• Works as the mechanical tension element within the hinge assembly to maintain normal door operation

• One spring hinge (single counterbalance spring)

• Install with power disconnected and door supported to prevent dropping or injury
• May require partial door removal or hinge access depending on appliance design
• Compare the new spring to the old part for correct orientation before installing
• If other hinge components show wear or damage, replace them at the same time for best performance

This mounting bracket secures internal components to the appliance frame to restore proper alignment and reduce movement. It's a simple replacement that helps eliminate rattles and keeps parts firmly in place. What it does:

• Provides a secure anchor point for internal parts to stop shifting during operation
• Prevents rattling, squeaking, or vibration caused by loose components
• Helps restore proper alignment when panels or assemblies sag or sit unevenly
• Replaces cracked or bent brackets that can cause part wear or misfit

• One mounting bracket

• Disconnect power and water before starting any repair
• Access may require removing panels or trim to reach the bracket location
• Use common hand tools (screwdriver, nut driver) and retain hardware for reuse
• Inspect surrounding clips and fasteners and replace any that are damaged for a secure fit

The Pressure Regulator is an OEM replacement part for Bosch gas cooktops. It maintains consistent burner flame levels for precise meal preparation, maximizing fuel efficiency. Even pressure safeguards safety through controlled gas flow.

Causes of a bad pressure regulator can include deteriorating diaphragm seals or valve shafts due to repetitive operations over the appliance's lifespan. Mineral scales from sediment in gas lines threaten integrity.

Symptoms of a bad pressure regulator include:

• Flames lift or flare away from burner heads unpredictably   
• Burners cannot maintain set heat levels, constantly cycling 
• Difficulty achieving desired flame height or cooktop shuts off
• Potential safety hazards like uncontrolled gas leakage

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.