Thermador Range / Cooktop / Oven Gasket & Seal

The Burner Gasket is an OEM part for Bosch cooktops and ranges. It provides a seal between the burner and the cooktop surface, preventing gas leaks and ensuring efficient operation.

Causes of a bad burner gasket can include wear and tear from frequent use, exposure to high temperatures, or damage from cleaning activities. Over time, the gasket may become brittle or develop cracks, compromising its sealing ability.

Symptoms of a bad burner gasket include:

• Gas odors near the cooktop
• The burner not igniting properly
• Visible cracks or deterioration in the gasket
• The burner not sitting securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The oven door gasket is the heat-resistant seal around the 30-inch oven cavity. It helps the oven reach and hold temperature, preventing heat and steam leaks, and replaces a worn or damaged seal for consistent baking results.

• Seals the door-to-cavity gap to limit heat and moisture loss
• Restores proper door compression to help maintain accurate temperatures and normal preheat times
• Replaces gaskets that are torn, frayed, flattened, brittle, or stretched
• Common symptoms: hot air or steam escaping at door edges, temperature fluctuations, longer cook times, or a door that no longer closes snugly

• Disconnect power and allow the oven to cool completely before servicing
• Open the door and remove the old gasket, noting seam orientation and where the ends seat
• Clean the mating surfaces; install the new gasket with the seam at the bottom center, seating the ends fully into the factory holes/retainers without overstretching
• Close the door and check for uniform contact around the perimeter

This door seal restores a tight barrier between the oven door and cavity. Replacing a worn gasket helps your oven reach and hold temperature, reduces heat escaping at the door edges, and supports more consistent baking and roasting results.

• Creates a heat-resistant seal around the oven opening
• Helps the oven preheat and maintain set temperature
• Limits heat, steam, and odors from escaping at the door
• Typical signs it needs replacement: visible tears or flattening, heat felt around the door, longer preheat/cook times, or uneven baking

• Disconnect power at the breaker and let the oven cool completely
• Open the door, pull the old seal from its channel, and clean the groove
• Press the new seal evenly into the channel without stretching; ensure corners seat fully
• Close the door to verify uniform contact all around and adjust as needed

The Oven Door Gasket Kit is an OEM replacement part for 27" Bosch wall ovens. It includes a gasket for insulating the oven cavity while in use and clips to secure it. Over time, heat and compression can break down gasket material allowing potential leaks of hot air from the oven during cooking or difficulty closing the door. Causes involve standard wear from repetitive door closing as well as exposure to high oven temperatures over many heating cycles.

Symptoms of failed gaskets include: 

• excessive heat escape from the door opening
• Door locking difficulties
• visible cracks or tears in the gasket materials 

Replacing the gasket allows for smooth door movement and an tight seal when closed. This Bosch part can also be used on Thermador and Gaggenau appliances.

This door seal creates a watertight barrier between the dishwasher door and tub to contain wash water and steam. Replace a worn gasket to stop drips from the door area and restore a reliable, quiet seal.

• Seals the perimeter of the door to help prevent leaks at the sides and top
• Helps the door close snugly and contain moisture/steam
• Replaces seals that are cracked, flattened, deformed, or shedding pieces
• Typical symptoms: water on the floor near the door, dampness around the door frame, visible wear, door harder to close

• Disconnect power and turn off water supply before servicing
• Pull the old seal straight out; clean the groove/channel of residue and debris
• Warm the new seal to relax it; start at the top center and press it fully into the groove, ensuring corners are evenly seated
• Close the door for several hours to help the seal set, then run a short test cycle and check for leaks

This side-trim gasket seals the edge of the appliance door/trim to help maintain a clean fit and reduce rattling or light air leakage. It restores the door edge seal for a neater appearance and improved closing performance. What it does:

• Seals the door side trim to help reduce noise and prevent light air or moisture intrusion
• Helps maintain proper alignment and fit of the door trim for smooth opening and closing
• Replaces worn, torn or compressed trim gasket that can cause rubbing or gaps
• Supports overall door aesthetics by restoring a continuous seal line

• One side-trim gasket

• Basic trim removal may be required
• Inspect mating surfaces and remove old adhesive or debris before installing the new gasket
• Use gentle pressure to seat the gasket; avoid stretching or over-tensioning
• Disconnect power to the appliance before doing any service that exposes electrical components

This 65-inch door gasket seals the appliance door to help maintain proper temperature and prevent leaks. It replaces a worn or torn gasket to restore a tight seal and improve efficiency. What it does:

• Creates an airtight seal around the door to help prevent water leaks and air loss
• Helps maintain consistent internal temperature and protect contents
• Reduces drafts and minimizes moisture buildup that can cause odor or frost
• Common symptom: visible cracks, tears, flattening, or water leaking from the door

• Install on a clean, dry door surface; follow OEM alignment to ensure an even seal
• Inspect door frame and mounting channel for damage before installing the new gasket
• Gasket may need gentle warming or seating to fit snugly in the channel (avoid open flame)
• Disconnect power/water if removing door panels or working near electrical components

This is a replacement door gasket that restores a tight seal around the appliance door to help prevent leaks and reduce energy loss. Designed to match the OEM fit and form for reliable sealing performance. What it does

• Creates a full door seal to help keep water, steam, heat, and cold where they belong.
• Helps stop common leak symptoms such as water pooling or dripping from the door.
• Can reduce energy loss and cycling caused by a worn or damaged seal.
• Visible wear, tears, compression, or gaps are common signs the gasket needs replacing.

• Disconnect power and, if applicable, water supply before beginning any service.
• Remove the door panel or trim only if required by your model; follow manufacturer instructions.
• Clean the gasket channel and seating surface before installing the new gasket for best fit.
• Press the gasket into the channel evenly; avoid stretching or pinching the seal during installation.

This umbrella-style seal fits around the dishwasher pump shaft to help prevent water from leaking between the pump and the tub. It keeps the pump assembly sealed so your dishwasher can drain and run without unwanted leaks. What it does:

• Forms a flexible watertight barrier around the pump shaft to reduce leaks at the pump/tub interface
• Helps maintain proper drainage by keeping pump openings sealed
• Commonly replaced when you find water pooling under the dishwasher or active leaks near the pump area
• Designed to resist dishwasher detergents and typical wash temperatures

• Disconnect power and shut off water before starting any repair.
• Access typically requires removing the dishwasher toe kick and possibly the pump assembly; follow the service manual for your model.
• Inspect the pump housing and surrounding seals/fasteners; replace any damaged components to restore a reliable seal.

This genuine-style door gasket seals the dishwasher door to the tub to help prevent leaks and maintain proper wash performance. It restores a snug, even seal when the original gasket is cracked, torn, or worn. What it does:

• Creates a watertight seal between the dishwasher door and tub to reduce leaks during cycles
• Helps maintain consistent wash and dry performance by keeping water and steam inside the tub
• Reduces door rattling and dampens vibration caused by a compressed or damaged seal
• Common symptom: water pooling or dripping from the door edge, visible tears, gaps, or persistent odor from trapped moisture

• One door gasket / seal

• Disconnect power and water to the appliance before attempting any service
• Remove the inner door panel or access trim per your model's service instructions to replace the gasket
• Check the gasket seating channel for debris or damage and clean before installing the new seal

This 1/2-inch foam adhesive tape cushions and seals appliance gaps to reduce vibration and prevent rubbing or rattling of panels. It's a simple, flexible trim that restores fit and quiets noisy or loose parts. What it does:

• Provides a soft, compressible barrier to reduce panel-to-panel contact and eliminate rattles
• Helps seal small gaps to keep out dust and reduce drafts around doors or trim
• Cushions components to damp vibration and protect finishes from wear
• Conforms to irregular surfaces for easy placement in tight spots

• Access the area with the appliance powered off and, if applicable, unplugged for safety
• Clean and dry the surface before applying for best adhesion
• Cut to fit with scissors or a utility knife and press firmly to set the adhesive
• Replace if the foam is compressed, torn, or no longer adheres