Parts for Maytag MGD4100DW0: 02 - Top And Console Parts

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This console shell is the outer housing that covers the dryer control area and delivers a clean, finished appearance while protecting internal controls. It restores the dryer's original look and shields electronics from dust and wear. What it does:

• Replaces the damaged or cracked control console housing to restore fit and appearance
• Protects control board, switches, and wiring from lint and debris
• Provides the mounting surface for control knobs, buttons, and bezels
• Helps prevent moisture and dust from reaching internal components, reducing nuisance issues

• Disconnect power before starting; this part requires access behind the console
• Remove control knobs and trim as needed to free the old shell; retain screws and hardware unless replacements are supplied
• Handle edges carefully to avoid scratching the finish during installation

A direct-replacement control panel assembly that restores the appliance's front user interface so you can select cycles and settings easily. Replaces a damaged, cracked, or unresponsive control surface to regain normal control operation. What it does

• Houses the touchpad/buttons and display area used to select oven/range functions and temperatures.
• Replaces worn, cracked, or unresponsive front controls that cause buttons or the display to fail.
• Can resolve issues with unresponsive key presses or missing/obscured display segments when paired with a working control board.
• Provides the visible user interface and mounting surface for control electronics.

• Disconnect power at the breaker or unplug the appliance before starting—electric shock risk.
• Remove trim or screws securing the old panel; handle glass or plastic fascia carefully to avoid breakage.
• Some models require transfer of clips, trim, or button pads from the old panel—keep small parts organized.
• After installation, restore power and test all buttons and display functions before reassembling remaining trim.

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location

The Wire Harness is an OEM part for Whirlpool dryers. This wire harness is responsible for delivering power and electricity throughout the dryer and to its individual components. 

Causes of a bad wire harness can include fraying or exposed wires due to wear and tear over time, cracking or damage of protective casings that expose internal wirings, or malfunctioning connections that disrupt power flow.

Symptoms of a bad wire harness include:

• The dryer not starting or powering on
• Components like the drum or heating elements not working
• Buzzing or humming noises coming from inside the dryer
• Tripped or blown fuses
• Error codes or failure to progress through cycles properly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.