Parts for Whirlpool 7MWGD95HEDU0: 02 - Top And Console Parts

The Harns-Wire is an OEM part for Whirlpool electric and gas dryers. It is an assembly of wires and connectors that link internal dryer components together, allowing signals and power to flow properly through the system. 

Causes of a bad harness can include wire insulation cracking from dryer drum movement, severed conductors leading to power loss in certain circuits, or broken connectors interfering with components like motors or sensors.

Symptoms of a bad harness include:

• Inability to start or stop cycles automatically  
• Temperature fluctuations resulting in uneven drying
• Unexpected stops or failure to tumble clothes smoothly
• Activation of safety cutouts or circuit breakers

 This harness is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers. 

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

A replacement control knob that restores reliable manual control of a dial or selector. Fits standard splined control shafts to make setting temperatures, cycles or power levels easy and intuitive. What it does

• Provides a secure grip and clear rotation for selecting settings on the appliance's control shaft
• Replaces cracked, worn or missing knobs that are hard to turn or won't stay in position
• Restores tactile feedback and alignment so settings register correctly with the control shaft
• Useful when original knob splines are stripped or the outer cap is damaged

• Typically installs by aligning splines and pushing firmly onto the control shaft until seated
• Power to the appliance should be turned off when removing and installing control parts
• Do not force the knob onto a shaft that does not match; verify spline match before installation
• If knob does not engage or control still fails, the underlying switch or shaft may need inspection

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.