Parts for Whirlpool WED92HEFBD0: 02 - Top And Console Parts

This is the appliance's cabinet top panel in a chrome finish. It replaces a dented, bent, or rusted top to restore a clean appearance and a secure fit while protecting internal components and supporting mounted parts.

• Forms the finished top surface of the cabinet (chrome finish)
• Shields internal components from debris and accidental contact
• Provides mounting/support points for the console, hinges, or brackets (varies by model)
• Addresses damage, corrosion, looseness, or rattling from a bent or missing top

• Disconnect power before servicing; wear cut-resistant gloves (sheet-metal edges are sharp)
• Retain and reuse the original screws/clips; transfer any brackets from the old panel
• Fasteners are typically at the rear or beneath the console—support the panel, remove screws, then lift off
• Align the new panel and tighten fasteners evenly to ensure a secure, rattle-free fit

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This wire harness routes power and signals between controls and components so the appliance operates correctly. It replaces a damaged or worn wiring assembly to restore reliable electrical connections and control response. What it does:

• Carries power and control signals between the control board and components
• Restores intermittent or lost function caused by broken, frayed, or burned wires
• Helps eliminate faults, error codes, or component failures related to poor connections
• Maintains correct connector fit and routing to prevent chafing or shorting

• Disconnect power before beginning any repair to avoid shock or injury
• Handle connectors by the plug body; avoid pulling on wires to prevent damage

Console shell replaces the dryer's outer control housing to restore a clean, secure surface for the control assembly and controls. It repairs cosmetic damage while providing the proper mounting surface for the control components. What it does:

• Covers and protects the control assembly from impact, dust, and debris.
• Provides the structural mounting surface for knobs, switches and the control interface.
• Common symptoms it addresses: cracked, dented, warped or split console and loose or misaligned controls.
• Restores the dryer's appearance and helps prevent further damage to internal control components.

• Disconnect power (unplug the dryer or shut off the circuit breaker) before beginning any work.
• Removal/installation typically requires removing the dryer top or front panel; basic hand tools (screwdriver, nut driver) are commonly used.
• Handle any sharp sheet-metal edges with care and wear gloves and eye protection.

The Harns-Wire is an OEM part for Whirlpool electric and gas dryers. It is an assembly of wires and connectors that link internal dryer components together, allowing signals and power to flow properly through the system. 

Causes of a bad harness can include wire insulation cracking from dryer drum movement, severed conductors leading to power loss in certain circuits, or broken connectors interfering with components like motors or sensors.

Symptoms of a bad harness include:

• Inability to start or stop cycles automatically  
• Temperature fluctuations resulting in uneven drying
• Unexpected stops or failure to tumble clothes smoothly
• Activation of safety cutouts or circuit breakers

 This harness is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dryers. 

The Control Panel is an OEM part for Whirlpool dryers. It houses the electronic controls and touchpad responsible for operating all dryer functions like heat settings, cycles, and time selections. The control panel is designed for easy accessibility and programmability.

Causes of a bad control panel can include water damage, faulty electronic components, or non-functioning buttons or display.

Symptoms of a bad control panel include:

• Inability to start or stop cycles
• Malfunctioning or unresponsive buttons
• Fault codes or error messages appearing
• Inaccurate time or temperature readings

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

The Knob Spring Clip is an OEM part for Whirlpool appliances, specifically designed for use in washers and dryers. This small but essential component is responsible for securing the control knob to the control panel, ensuring that the knob stays firmly in place during operation.

Common causes of a bad spring clip include frequent use, accidental impacts, or wear and tear over time. A faulty spring clip can result in the control knob becoming loose or falling off, making it difficult to operate the appliance.

Symptoms of a bad knob spring clip include:

• The control knob is loose or wobbly
• The control knob falls off easily
• Difficulty in turning or setting the control knob
• The appliance not responding correctly to knob adjustments

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This name plate is the cosmetic identification plate for the appliance's console, restoring factory appearance and readable markings. It replaces a cracked, faded, or missing plate to make the console easy to read and look finished. What it does:

• Provides the external identification/branding plate for the control area or console
• Restores legible markings that can become faded, scratched, or worn
• Improves overall appearance when the original plate is damaged or missing
• Protects the underlying console surface from minor wear

• One name plate as shown

• Disconnect power to the appliance before starting any work
• Installation may require removing trim or console screws or peeling off old adhesive
• Handle carefully to avoid scratching the new plate; align before fastening or applying adhesive