Parts for Whirlpool WED95HEDC0: 02 - Top And Console Parts

Top panel for dryers. Covers and protects the dryer's upper surface. Replace if your original panel is dented, cracked, damaged, or worn from use.

Chrome finish cabinet top panel for dryers. Replaces dented, bent, or rusted top panels to restore clean appearance and secure fit over internal components.

Replaces the upper cabinet cover of your dryer. Needed when the original panel is dented, rusted, warped, or damaged. Restores a secure fit and clean look.

Control console assembly for dryers. Mounts on top of the dryer cabinet and houses the control panel. Replace if cracked, damaged, or broken.

Console mounting bracket for dryers. Secures the control panel to the cabinet. Replace if cracked, bent, or broken to restore proper console support.

A replacement control knob that restores reliable manual control of a dial or selector. Fits standard splined control shafts to make setting temperatures, cycles or power levels easy and intuitive. What it does

• Provides a secure grip and clear rotation for selecting settings on the appliance's control shaft
• Replaces cracked, worn or missing knobs that are hard to turn or won't stay in position
• Restores tactile feedback and alignment so settings register correctly with the control shaft
• Useful when original knob splines are stripped or the outer cap is damaged

• Typically installs by aligning splines and pushing firmly onto the control shaft until seated
• Power to the appliance should be turned off when removing and installing control parts
• Do not force the knob onto a shaft that does not match; verify spline match before installation
• If knob does not engage or control still fails, the underlying switch or shaft may need inspection

This is a gray plastic timer knob that attaches to the dryer's control panel shaft. It allows you to select and set the drying cycle and time. Replace this knob if it is cracked, broken, or if the D-shaped shaft hole is worn out, causing the knob to spin freely without engaging the timer.

This is a chrome-finished timer knob that attaches to the timer shaft on the dryer's control panel, allowing you to select and start drying cycles. It is made of plastic with a metallic chrome appearance. Replace this knob if it is cracked, broken, or no longer grips the timer shaft properly, making it difficult to turn or set the dryer cycle.

Internal wire harness assembly that connects dryer components for signal and power flow. Replace if wires are cracked, frayed, or connectors are damaged.

Fix unresponsive buttons or a blank display with a new dryer control panel. This repair restores cycle selection and settings. Moderate DIY install.

Replace your dryer's control panel if the existing panel is cracked, damaged, or worn. This panel houses the controls and display on the front of your dryer.

Fixes unresponsive buttons, blank display, or cycle selection issues. Direct replacement control panel for dryers. Moderate DIY repair in 30-45 minutes.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Mounting screw for microwaves, dryers, wall ovens, washers, and laundry centers. Replaces lost, stripped, or damaged screws during installation or repair.

This is a D-shaped knob insert or spring clip that fits inside a control knob and connects it to the control shaft on the dryer's front panel. It ensures the knob grips the shaft properly so you can turn the timer or selector. Replace this insert if your control knob spins freely without engaging the shaft or if the knob feels loose and won't stay in position.

This name plate is the cosmetic identification plate for the appliance's console, restoring factory appearance and readable markings. It replaces a cracked, faded, or missing plate to make the console easy to read and look finished. What it does:

• Provides the external identification/branding plate for the control area or console
• Restores legible markings that can become faded, scratched, or worn
• Improves overall appearance when the original plate is damaged or missing
• Protects the underlying console surface from minor wear

• One name plate as shown

• Disconnect power to the appliance before starting any work
• Installation may require removing trim or console screws or peeling off old adhesive
• Handle carefully to avoid scratching the new plate; align before fastening or applying adhesive

Color: Grey