Parts for Maytag MED6000XG0: 01 - Top And Console Parts

This top panel is the upper cover of your dryer's cabinet. Replace a dented, rusted, or warped panel to restore a secure, flush fit and the clean, finished look of your machine.

• Forms the dryer's upper cabinet surface and covers internal components
• Provides proper mounting/alignment for the control console and top hardware
• Helps maintain cabinet rigidity and a solid, secure fit
• Common signs it's needed: visible dents/bends or rust, top won't sit flush or stay secured, gaps or misalignment near the console

• Disconnect power; shut off gas supply for gas models
• Wear cut-resistant gloves—cabinet edges can be sharp
• Remove fasteners securing the top, lift off, and transfer any clips/insulation from the original panel
• Align the new panel and tighten fasteners evenly to ensure a flush, secure fit

This wire harness is the main wiring assembly that connects control components and power circuits for proper operation. Replacing a damaged harness restores reliable electrical connections and reduces intermittent operation or no-power issues. What it does:

• Provides factory routing and secure connections between controls, sensors, and power input
• Restores lost or intermittent electrical continuity that can cause failures or erratic behavior
• Prevents shorts and arcing from damaged or frayed wiring
• Helps ensure signals reach the control board and associated components

• Disconnect power before servicing to avoid shock or damage
• Inspect connector ends and routing; replace any retaining clips or fasteners damaged during removal
• Route harness to avoid sharp edges and heat sources; secure with existing clips or zip ties as needed

This 8-18 x 5/8-inch screw secures appliance panels, brackets, and covers. Replacing a missing or stripped fastener restores a tight fit and helps prevent vibration or loosening where this exact size is specified.

• Fastens sheet-metal or plastic components where a #8-18 x 5/8 screw is called for
• Helps maintain alignment and reduce rattling or vibration
• Replaces stripped, corroded, or missing screws of the same size
• Common symptoms: loose panels, gaps/poor fit, rattling noises, or visible missing hardware

• Disconnect power and shut off gas/water (as applicable) before service
• Match thread and length to the original; replace screws one at a time to keep parts aligned
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• If the receiving threads are damaged, additional repair (clip, insert, or new nut) may be needed

This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.

Replacement control knob that restores manual command of heat and function settings on compatible Whirlpool appliances. Its push-on design gives a secure grip and straightforward replacement for cracked, stripped, or missing knobs. What it does:

• Lets you set and adjust temperature, burner heat level, and basic oven or cooktop functions.
• Restores control when the original knob is loose, cracked, stripped, or missing.
• Push-on fit provides a secure connection to the control shaft and reliable tactile feedback.
• Improves visibility and usability when original markings have worn away.

• Disconnect power or unplug the appliance before servicing to reduce risk of shock or injury.
• Remove the old knob by pulling it straight off the control shaft; avoid twisting or levering against adjacent parts.
• Align the knob indicator with the control shaft splines and push the new knob fully onto the shaft until seated.
• Reconnect power and test controls at low settings to ensure proper fit and operation.

This is a replacement mounting screw used to secure appliance panels and small components. It provides a correct-fit fastener to restore secure attachment and eliminate rattles or loose parts. What it does:

• Secures trim, panels, brackets, or small assemblies to prevent movement and vibration
• Restores proper alignment when a worn or missing screw causes loose parts or noise
• Works as a direct-replacement fastener where the OEM screw specification is required

• One replacement screw

• Use the correct driver bit to avoid stripping the head; do not overtighten
• Disconnect power and follow appliance safety guidelines when accessing internal components
• If the original mounting hole or threads are damaged, repair or replace the mounting hardware before reinstalling