Parts for Lg 31553: Top Cover Assembly Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Protective cover for washer control panel or component housing. Replaces cracked, broken, or missing covers. Shields internal parts from damage.

Fix fabric softener leaking or not dispensing with this washer dispenser cap. Seals the reservoir and directs softener flow during the wash cycle.

Replace your washer's control panel housing case if cracked, broken, or damaged. This protective cover secures and shields internal components.

Fix loose or missing dispenser trim with this washer cover cap. Snaps into place to protect fastener openings and restore a clean, finished look. Easy DIY fix.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Secures internal washer components in proper alignment. Replace this mounting bracket if cracked, rusted, broken, or missing to restore stability.

Secures internal components to the washer frame. Replace if your bracket is cracked, rusted, broken, or missing to restore stable support and alignment.

This noise filter assembly is an electronic component that suppresses electromagnetic interference generated by the washer's motor and control board. It is typically mounted near the power inlet and helps protect other household electronics from electrical noise. Replace this assembly if your washer fails to start, trips a breaker, or if the filter housing appears burned or damaged.

Fix a washer that won't start, stop mid-cycle, or display error codes. This main power control board manages motor, pump, and heating functions.

Leaking water behind your washer? A cracked inlet hose is often the culprit. This hose channels water from your supply line into the machine during fill.

The Display PCB Assembly is an OEM component specifically designed for LG washers. Housed within the digital control panel, this printed circuit board coordinates the interface between users and the washer. Integrated microchips and programs process commands to start cycles and display settings.

Symptoms of a bad display PCB include:

• Dim, unresponsive, or blank control panel display
• Stuck or unresponsive buttons  
• Erratic or failed cycle/option selections
• Diagnostic error codes shown

Causes can include water damage or power surges damaging circuits over time. Without a functioning interface board, users cannot easily operate basic functions or monitor wash status.

This OEM LG part restores the dependable control experience. Compatible also with Sears/Kenmore models, it provides direct fit and restoration of core washing controls. Proper installation protects future operations while maintaining convenience.

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

Fix a leaking or cracked fabric softener dispenser with this washer softener cap. Easy DIY repair with no tools needed—just remove and replace in minutes.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

Fix dispenser overflow or leaking issues with this washer detergent drawer assembly. Channels water through detergent and softener compartments. DIY repair.

Connects water inlet valve to tub in your washer. Replace if cracked, leaking, or ports are stripped. Ensures secure, leak-proof connection during cycles.

Fix DL error code or washer that won't start with this lid switch and lock assembly. DIY repair in about 20 minutes with basic tools and video guide.

Fix washer overfilling or not filling issues with a water level pressure switch replacement. Common repair for PE error codes. Takes 10-20 minutes to install.

Washer won't fill or won't stop filling? This water inlet valve controls water flow into the tub. DIY-friendly repair, typically takes 10-15 minutes.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.