Parts for Electrolux EW30GS75KSC: 09 - Top / Drawer Parts

This is a metal or finished side panel that attaches to the warming drawer section of the range. It provides structural support and a clean exterior appearance on the side of the drawer compartment. Replace this panel if it is dented, scratched, rusted, or missing, which can affect both the look and proper operation of the warming drawer.

Decorative trim piece for range oven door. Replaces cracked, chipped, or missing trim. Installs along door edge to restore finished appearance.

Gas burners won't ignite and there's no clicking sound? The spark module provides the electrical spark to light all burners. DIY repair in under 1 hour.

This is the outer frame for a warming drawer, finished in black. It surrounds the drawer front and provides structural support as well as a finished appearance. Replace this frame if it is bent, cracked, or if the drawer no longer sits flush with the range body.

Cast iron grate that sits on top of your range burner. Replace if cracked, broken, or chipped from drops or wear. Ensures stable pot and pan support.

Replace your damaged or deformed range cooktop grate to restore stable support for pots and pans. Essential when your grate is cracked, warped, or broken.

Burner cap for gas cooktop. Sits on top of the burner base to direct and distribute flames. Replace if cracked, chipped, discolored, or missing.

Replacement burner cap for gas cooktop surface burners. Installs on top of burner head to center and shape the flame. Replace if cracked, chipped, or missing.

Removable griddle plate that sits over range burners to create a flat cooking surface. Replace yours if cracked, warped, or worn for even cooking.

Replacement spacer for ovens and ranges. Maintains proper spacing between components. Replace if cracked, broken, or missing to restore alignment.

Insulation panel for gas ranges. Installs inside the range cavity to provide sound dampening and thermal protection. Replace if torn, damaged, or missing.

This is the electric heating element located inside the warming drawer of a range. It provides low, steady heat to keep cooked food warm until serving. Replace this element if the warming drawer no longer heats, heats unevenly, or if the element is visibly damaged or burned out.

Oven not heating to set temperature or heating too slowly? This thermostat controls oven temperature cycling. Test for continuity to diagnose the issue.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Replace your range's control panel if the original is cracked, damaged, or showing wear. This panel mounts to the front and houses control components.

Range drawer glide with integrated ball bearings ensures smooth drawer operation. Replace when drawer sticks, won't close, or bearings are bent or damaged.

This wiring harness is the factory-style electrical assembly that connects appliance controls and components for reliable power and signal routing. Replacing a damaged harness restores proper electrical connections and helps resolve intermittent or failed operation. What it does:

• Routes power and control signals between the control module and components
• Restores reliable electrical connections when wires or connectors are damaged
• Helps correct symptoms such as intermittent power, failed cycles, or non-responsive controls
• Prevents shorts and arcing caused by exposed or frayed wiring when correctly installed

• Disconnect power (unplug appliance or switch off breaker) before servicing to avoid shock or injury
• Inspect connectors and mounting points; secure harness away from heat and moving parts
• Use proper strain relief and routing to prevent chafing or contact with sharp edges

This is a flexible gasket that seals the gap around the main cooktop surface on a range or oven. It prevents heat from escaping and keeps grease, moisture, and debris from getting beneath the cooktop. Replace this gasket if you notice heat escaping from around the top, if the seal appears cracked, hardened, or no longer lies flat.

Rubber bumper that cushions your range door, reducing noise and preventing wear. Replace if cracked, missing, or worn to restore proper door contact.

Mounting screw for electric range, oven, or wall oven assembly. Secures internal components and panels. Replace if stripped, missing, or damaged.

Replacement mounting screw for refrigerators, ovens, ranges, and cooktops. Secures interior panels, components, and trim. Needed when original is stripped, missing, or damaged during repair.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment