Parts for Frigidaire FFEF3016TMB: Top / Drawer Parts

This liner attaches to the inside of the range's storage or warming drawer front panel, providing a finished interior surface and insulation. It helps protect the outer drawer panel from heat generated by the oven cavity above. Replace this liner if it is warped, cracked, discolored, or missing, which can allow excess heat to reach the drawer's exterior.

This control panel is the front console fascia that houses the range's touchpads and display, restoring a complete, finished look and enabling user control. It replaces a cracked, faded, or non-responsive console surface to improve usability and appearance. What it does

• Provides the user interface surface for the range's keypad and display so buttons and indicators are visible and accessible
• Restores a secure mounting surface for control components and helps protect internal electronics from debris
• Addresses symptoms like cracked or warped fascia, peeling finish, or cosmetic damage that interferes with normal use
• Works with existing control electronics; does not include electronic control board or keypads unless explicitly stated

• One control panel (console front) as shown

• Installation requires removing the range backguard or console trim; follow manufacturer service instructions
• Disconnect power at the breaker before starting to avoid shock or damage
• Handle the panel and any attached lens or display carefully to avoid scratching; retain and transfer any clips or hardware unless new hardware is supplied

Rear glide attaches to the back of your range storage drawer, allowing smooth sliding motion. Replace if broken, cracked, or missing to prevent drawer tilt.

Drawer slide glide for electric and gas ranges. Replace if cracked, broken, or worn to restore smooth, aligned drawer movement and eliminate sticking.

If your burner isn't heating evenly or won't heat at all, this 6-inch coil element typically solves the problem. Simple plug-in replacement. Video guide.

The Coil Surface Element is an OEM part for Frigidaire ranges and cooktops. It is a key component for cooking, providing the heat source directly under pots and pans. This 8 inch element is designed to heat quickly and maintain consistent temperature, which is essential for effective cooking and energy efficiency.

Symptoms of a bad Coil Surface Element include:

• The element not heating up when turned on
• Uneven heating or hot spots that can cause inconsistent cooking results
• The element not turning off or fluctuating in temperature

Causes of a bad coil surface element can include a breakdown of the coil itself due to general wear and tear, electrical connections becoming loose or corroded, or damage from spills or impacts during cooking.

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Main top replaces the cooktop surface on select ranges, restoring a flat, secure surface for burners and controls. It improves appearance and supports proper burner alignment for safer, more reliable cooking. What it does:

• Provides the primary cooktop surface and mounting for surface burners and elements.
• Restores a flat, undamaged surface when the original top is dented, warped, cracked, or cosmetically damaged.
• Secures burner assemblies and helps prevent burner wobble or misalignment.
• Improves cleanability and overall appearance of the cooktop area.

• Disconnect power (and gas supply for gas ranges) before beginning service.
• Remove burner grates, surface elements, and any trim; retain original hardware for reassembly.
• Large parts may require two people to position; use basic hand tools and follow model-specific service instructions.
• Verify burner alignment and function before completing reassembly.

Main top support rod for electric ranges. Replacement needed when original rod is broken, bent, or damaged. Installs to provide structural support.

Replace cracked, rusted, or stained drip pans under your range burners. Catches spills and protects cooktop. Easy snap-in installation, no tools needed.

Chrome drip pan installs beneath range burner elements to catch spills and drips. Replaces cracked, rusted, or worn pans for a clean cooktop appearance.

Burner not heating? This receptacle kit restores electrical connection to cooktop elements. Most DIYers complete this repair in under 30 minutes.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Size: 6-20 x 0.312 inch.

Size: 8-32t x 0.500 inch. Color: Black.

This kit includes a surface element receptacle block and wiring harness that connects a burner element to the range's electrical system. It transfers power from the terminal block to the heating element on the cooktop. Replace this kit if your surface burner heats intermittently, fails to heat at all, or you see scorching or burn marks around the receptacle connections.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.