Parts for Frigidaire FFGH3054USE: Top / Drawer Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This replacement refrigerator cabinet liner restores the appliance's interior surface, helping contain spills and support shelves/drawers for reliable storage. Fits specific Frigidaire models; use the part number on your unit. What it does:

• Replaces cracked, warped or damaged interior surface that can allow moisture, odors, and debris to collect
• Provides the finished interior surface that supports shelf and bin mounting points
• Helps maintain a clean, easy-to-wipe interior and prevents insulation exposure
• Reduces the risk of leaks by restoring the proper fit and seals where the liner meets doors and gaskets

• One refrigerator cabinet liner as shown

• Disconnect power and empty the refrigerator before starting; follow manufacturer safety guidance
• Installation generally requires removing shelves, drawers and trim; small fasteners or clips may secure the liner
• Avoid sharp tools to prevent damage; inspect surrounding seals and hardware while replacing the liner

This metal shield protects internal components from heat, debris, and wear, helping the appliance run safely and reliably. It replaces damaged or missing shields to restore proper protection around sensitive parts. What it does:

• Shields wiring and components from heat and debris to prevent damage
• Helps reduce risk of shorting or component exposure caused by a damaged panel
• Common symptom: visibly bent, warped, or corroded shield
• Common symptom: unusual odors or hot spots near the area the shield covers

• One replacement shield/trim panel as shown

• Disconnect power (and gas supply if applicable) before starting any repair
• Wear gloves to protect against sharp sheet-metal edges
• Retain and reuse original fasteners when possible; replace any stripped screws
• If accessing the shield requires removing other panels, keep track of hardware and order of removal

This glide replaces a worn or broken drawer slide to restore smooth, reliable movement. It helps the drawer open and close without sticking, improves alignment, and reduces noise or catching during normal use. What it does:

• Guides and supports the drawer along its track for consistent sliding action.
• Replaces glides that cause drawers to stick, bind, sag, or make noise.
• Helps maintain proper drawer alignment and prevents uneven travel or dropping.
• Intended as a service replacement for a damaged or worn glide.

• Disconnect power or unplug the appliance before beginning any service.
• Remove the drawer to access the glide; installation usually involves sliding or snapping the glide into place and securing with screws if required.
• Verify correct orientation and smooth operation before returning the drawer to regular use.

The Glide is an OEM part for Frigidaire ranges. It ensures smooth movement of the storage drawer, allowing you to easily access and organize your stored items.

A bad glide can be caused by wear and tear, damage, or lack of lubrication. Signs of a faulty glide include a sticky or jammed drawer, uneven sliding, or a drawer that doesn't close properly.

Symptoms of a bad glide can include:

• Difficulty in opening or closing the storage drawer.
• Uneven or jerky sliding motion of the drawer.
• Drawer getting stuck or not fully closing.

Replace your worn-out or damaged glide with this genuine OEM part to restore movement to your range's storage drawer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement glide helps a refrigerator or freezer drawer open and close smoothly and keeps the drawer aligned for reliable operation. It restores proper sliding action and reduces sticking or scraping. What it does

• Replaces a worn or broken drawer glide to restore smooth drawer movement
• Supports the drawer to prevent sagging and misalignment
• Helps reduce rubbing, sticking, and noisy operation during use
• Maintains proper drawer tracking so the drawer seats correctly

• Disconnect power to the appliance and remove food or contents from the drawer before starting
• Remove the drawer per your model's service instructions to access the glide
• Most installations are simple push-in or screw-replace procedures; keep fasteners from the original assembly

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

This main top is the finished cooktop surface for your range, providing a durable, easy-to-clean area that supports burners and grates while protecting internal components from spills and debris. What it does:

• Covers and protects the range's internal components and burner openings
• Supports burner elements, grates and cookware for stable cooking
• Helps contain spills for easier cleanup and prevents debris from entering the oven cavity
• Replaces cracked, chipped, badly scratched or warped cooktop surfaces that interfere with burner alignment

• Main top (1)

• Disconnect power and gas supply before starting any repair
• Remove grates, burner caps and control components as needed to access mounting screws
• Two people may be required to lift and position the main top safely to avoid damage
• Retain all mounting hardware and ensure burners and controls are properly seated after installation

This replacement cooktop grate provides a stable, heat-resistant support for cookware on your range, restoring safe, even cooking and preventing pots and pans from wobbling or scratching the cooktop surface. What it does:

• Supports cookware above the burner to allow proper flame coverage and consistent heating
• Replaces a cracked, warped, or damaged grate that causes cookware instability or uneven cooking
• Stops rattling or shifting that can occur when a grate no longer sits flat
• Protects the cooktop surface from direct contact with hot cookware

• Allow the range and grate to cool completely before removing or installing
• Lift the old grate off and set the new grate into place; no tools typically required
• Ensure the grate sits flat and is properly aligned over burners before use
• If you smell gas or detect a leak while working on a gas range, stop.

The Burner Grate is an OEM replacement part for Frigidaire ranges and cooktops. The burner grate distributes heat evenly across the base of cookware while allowing for easy viewing of cooking progress underneath. 

Causes of a bad burner grate can include warping, bending, rusting or cracking due to long-term high heat exposure. If left unaddressed, severely damaged grates can pose a safety concern.

Symptoms of a bad burner grate include:

• Unstable or uneven grill surfaces 
• Difficulty centering pots and pans properly
• Hot spots under cookware causing food to scorch 
• Grill bars dislodging or falling during cooking

This OEM part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the medium burner igniter on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a failing medium burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and instability

This cap is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, and Kenmore ranges

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the small burner igniter on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a bad burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and wobbling

This burner cap is compatible with Frigidaire, Gibson, White Westinghouse, Kelvinator, and Kenmore ranges.

The Burner Cap is an OEM replacement part that fits Frigidaire ranges. It is responsible for covering the large burner on the cooktop. Over time, the cap can become damaged from heat exposure and food debris. Causes of failure include cracking, warping, and corrosion. 

Symptoms of a failing burner cap include:

• Uneven or abnormal flame
• Ignition issues
• Improper fit and instability

This Frigidaire cap is also compatible with Gibson, White Westinghouse, Kelvinator, and Kenmore ranges

The Rear Filler Kit is an OEM part for Frigidaire ranges. It is responsible for sealing gaps and maintaining proper ventilation at the rear of the range. The filler kit prevents air leaks while allowing heat to properly escape from the oven cavity.

Causes of a bad rear filler kit can include normal wear and tear over time, damage that has compromised the sealing properties, or improper installation that has left gaps.

Symptoms of a bad rear filler kit include:

• Improper or uneven baking and broiling results
• Higher than normal temperatures on oven surfaces or cabinets nearby
• Excessive drafts or cold air felt around oven door or oven controls

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This genuine replacement door seal restores a tight refrigerator fresh-food compartment closure to help maintain even temperatures and reduce frost, moisture, and energy loss. Use when the original gasket is cracked, warped, or no longer seals. What it does:

• Creates an airtight barrier between the door and cabinet to keep cool air in and warm air out
• Helps prevent condensation, frost buildup, and uneven cooling in the fresh-food compartment
• Reduces compressor run time and energy waste caused by a failing seal
• Stops door gaps that can allow food spoilage or excess moisture

• One replacement door seal/gasket for the fresh-food compartment

• Unplug the appliance or switch off power before starting any work
• Clean the mounting surface and remove old adhesive or debris for a proper fit
• Warm and flex the gasket if needed (per OEM guidance) to align and seat it evenly; avoid overstretching
• Inspect and reuse or replace retainers/clips as required; test seal by closing the door and checking for gaps

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Size: 8-32t x 0.500 inch. Color: Black.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.