Parts for Frigidaire GLGS389EQA: 09 - Top / Drawer Parts

This is a metal or finished side panel that attaches to the warming drawer section of the range. It provides structural support and a clean exterior appearance on the side of the drawer compartment. Replace this panel if it is dented, scratched, rusted, or missing, which can affect both the look and proper operation of the warming drawer.

Gas burners won't ignite? A faulty spark module may be the issue. This part sends electrical current to igniters. DIY-friendly, takes minutes.

Low-friction slide piece that supports moving components in your range or wall oven. Replace worn or cracked glides to restore smooth operation.

Low-friction glide that supports and guides range drawer movement. Replace if cracked, broken, or worn to restore smooth sliding without sticking or scraping.

Replace your damaged, cracked, or missing range cooktop grate. Provides stable support for cookware over gas burners. Direct OEM replacement part.

Replace your cracked, chipped, or missing range burner cap. This cap sits on top of the burner base to direct flames evenly during cooking.

Rubber bumper cushions oven or range doors to reduce noise and prevent metal contact. Replace if cracked, worn, or missing to restore proper seating.

Color: Bisque. For white order 316270201.

This is a bisque-colored cover that fits over the oven vent opening on the rear of the cooktop surface. It allows hot air and steam to escape the oven cavity during cooking while keeping debris from falling inside. Replace this cover if it is cracked, discolored beyond the original bisque finish, or missing entirely.

Replacement insulation for range oven doors. Installs between door panels to retain heat and improve efficiency. Replace if compressed, torn, or missing.

This is the electric heating element located inside the warming drawer of a range. It provides low, steady heat to keep cooked food warm until serving. Replace this element if the warming drawer no longer heats, heats unevenly, or if the element is visibly damaged or burned out.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Replace your range's control panel if the original is cracked, damaged, or showing wear. This panel mounts to the front and houses control components.

Range drawer glide with integrated ball bearings ensures smooth drawer operation. Replace when drawer sticks, won't close, or bearings are bent or damaged.

This wiring harness connects the refrigerator's internal electrical components so the unit powers and communicates correctly. Replaces a damaged or burnt harness to restore reliable connections and stop intermittent or non-working circuits. What it does:

• Routes power and signal between control board, compressor, fans and other internal components
• Restores lost or intermittent power to affected parts when original wiring is damaged
• Helps eliminate symptoms like no cooling, intermittent operation, or visible wiring damage
• Prevents shorts and electrical arcing when faulty wires or connectors are replaced

• One wiring harness as shown

• Disconnect power at the breaker or unplug the appliance before starting
• Compare the new harness to the old one and follow OEM routing and connector orientation
• Secure harness away from moving parts and heat sources; ensure all connectors are fully seated

Protective shield that covers and guards the switch assembly on your range. Replace if the original shield is cracked, broken, or missing to restore proper coverage.

This wiring harness connects the refrigerator's internal electrical components so the unit powers and communicates correctly. Replaces a damaged or burnt harness to restore reliable connections and stop intermittent or non-working circuits. What it does:

• Routes power and signal between control board, compressor, fans and other internal components
• Restores lost or intermittent power to affected parts when original wiring is damaged
• Helps eliminate symptoms like no cooling, intermittent operation, or visible wiring damage
• Prevents shorts and electrical arcing when faulty wires or connectors are replaced

• One wiring harness as shown

• Disconnect power at the breaker or unplug the appliance before starting
• Compare the new harness to the old one and follow OEM routing and connector orientation
• Secure harness away from moving parts and heat sources; ensure all connectors are fully seated

Protective shield that covers and guards the switch assembly on your range. Replace if the original shield is cracked, broken, or missing to restore proper coverage.

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

Replacement #8 x 0.500 inch screw for securing panels, trim, and brackets in appliances. Needed when original fasteners are stripped, lost, or missing.

Specs: 8 - 18 x 0.500

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head