Parts for Kenmore 790.42623314 (79042623314, 790 42623314): Top / Drawer Parts

Storage drawer that installs at the bottom of your range. Replace if the drawer is cracked, warped, broken, or missing to restore storage functionality.

This is a metal or finished side panel that attaches to the warming drawer section of the range. It provides structural support and a clean exterior appearance on the side of the drawer compartment. Replace this panel if it is dented, scratched, rusted, or missing, which can affect both the look and proper operation of the warming drawer.

This spring installs inside your range to provide tension for various internal mechanisms. Replace if the spring is stretched, broken, or missing.

Secures the heating element to the cooktop surface. Replace if your original spring is broken, missing, or no longer holds the element firmly in place.

Oven rack glide enables smooth sliding of racks in your range. Replace if racks stick, don't slide smoothly, or glide is damaged. Verify fit with model.

Replace worn range oven rack glides to restore smooth sliding action. Essential when racks stick or don't glide properly. Verify fit with your model number.

Burner not heating or heating unevenly? This electric range surface element restores proper cooking temperature. Moderate DIY repair in 20-30 minutes.

This is a radiant heating element that sits beneath the glass surface of an electric cooktop or range. It generates heat for cooking when a burner is turned on. Replace this element if a burner no longer heats, heats unevenly, or fails to reach the correct temperature despite the control functioning properly.

This is a 180mm radiant surface induction element designed for use on a cooktop. It generates heat beneath the glass surface to cook food evenly. Replace this element if the corresponding burner no longer heats, heats unevenly, or fails to respond when turned on.

This 100W radiant element replaces a failed warming element to restore gentle, even heat in the appliance's warmer/drawer. It delivers low-profile radiant heat for keeping food warm between cooking and serving. What it does:

• Radiates low-level heat to maintain food temperature in the warmer or drawer
• Replaces a broken or non-heating warmer element
• Common symptom: warmer drawer not holding temperature or not heating
• Works as the heating element that sits under the warming surface to provide consistent warmth

• Disconnect power to the appliance before attempting service
• Inspect mounting and wiring; replace any damaged connectors or mounting hardware as needed
• Handle the element carefully to avoid bending or damaging the heating surface

Rubber bumper cushions oven or range doors to reduce noise and prevent metal contact. Replace if cracked, worn, or missing to restore proper seating.

This is a stainless steel door handle for a range or oven. It provides a grip point for opening and closing the oven door during everyday use. Replace this handle if it is cracked, loose, broken at the mounting points, or if the finish is worn or damaged.

This replacement storage box provides a secure, removable bin for holding food and small items inside the appliance. It restores organized storage and keeps contents contained for easy access and cleaning. What it does:

• Serves as a removable storage bin for shelving or drawer locations
• Holds produce, deli items, or other small food packages to prevent shifting
• Replaces cracked, chipped or missing bins that cause spills or poor organization
• Helps maintain proper airflow and visibility on the shelf when installed

• Remove food and empty surrounding shelves before installing
• Slide or snap the bin into its track until it clicks or seats fully; avoid forcing
• Inspect mounting rails or support tabs for damage and replace if worn
• Clean with mild soap and water; do not use abrasive cleaners or sharp tools

Replacement mounting screw that secures panels, trim, and components in ranges and ovens. Needed when original screws are lost, stripped, or damaged.

This is the electric heating element located inside the warming drawer of a range. It provides low, steady heat to keep cooked food warm until serving. Replace this element if the warming drawer no longer heats, heats unevenly, or if the element is visibly damaged or burned out.

Oven not heating to set temperature or heating too slowly? This thermostat controls oven temperature cycling. Test for continuity to diagnose the issue.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Replace your range's control panel if the original is cracked, damaged, or showing wear. This panel mounts to the front and houses control components.

Decorative finishing panel that covers exposed edges on your range for a clean appearance. Replaces cracked, broken, or missing trim to restore look.

Range drawer glide with integrated ball bearings ensures smooth drawer operation. Replace when drawer sticks, won't close, or bearings are bent or damaged.

Motor making noise or loose? This motor mounting nut secures motors in refrigerators, ranges, and other appliances. Simple install takes 15 minutes.

A flat replacement washer that helps secure fasteners and maintain proper spacing in the appliance. Use this part to restore a tight, stable connection where a small hardware washer is required. What it does:

• Provides a stable bearing surface for screws and bolts to prevent pull-through
• Maintains proper spacing and alignment between mating parts
• Helps reduce loosening from vibration that can cause noise or part movement
• Commonly used anywhere a small metal washer is required to secure assemblies

• Disconnect power to the appliance before beginning any repair to avoid shock or injury.
• Turn off water supply and move the appliance if needed to access fasteners safely.
• Use the correct-size screwdriver or socket; replace any fasteners that are damaged.
• Do not overtighten—tighten fasteners just enough to secure the parts without deforming the washer.

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.