Parts for Kenmore 790.93013317 (79093013317, 790 93013317): Top / Drawer Parts

This lower drawer replaces a damaged or missing bottom drawer on your range, restoring smooth slide action and a flush, finished look so the lower compartment operates correctly and the appliance is complete again.

• Forms the pull-out compartment beneath the oven for convenient access
• Interfaces with the drawer slides to open and close smoothly
• Restores proper alignment and full closure at the base of the range
• Typical symptoms: drawer jams, falls off tracks, sits unevenly, or is bent/dented

• Disconnect power and shut off gas; allow the range to cool before servicing
• Pull the old drawer out and lift to disengage from the slides; transfer any reusable parts as needed
• Set the new drawer onto both slides evenly and test for smooth travel and full closure
• If the drawer doesn't seat flush, re-check slide engagement and appliance leveling

This interior refrigerator liner provides the finished, easy-to-clean surface for the fresh food compartment and helps support shelves and bins. It restores the cabinet interior to factory condition for proper fit and appearance. What it does:

• Replaces a cracked, warped, or stained interior cabinet surface.
• Provides a smooth, washable surface that helps keep food area sanitary.
• Supports mounted shelves, drawers, and trim pieces in the compartment.
• Restores proper alignment and sealing where the liner mates to refrigerator components.

• Disconnect power and remove all food and removable shelves/bins before starting.
• Typical installation requires removal of trim and fasteners; keep hardware accessible for reassembly.
• Handle carefully to avoid scratching the finished surface and to prevent injury from sharp edges.

Size: 10-24 x 1.375 inch.

This glide is a replacement drawer slide that helps refrigerator/freezer drawers open and close smoothly and stay aligned. It restores proper drawer movement and reduces sticking or scraping for easier access to stored items. What it does:

• Supports and guides the drawer along its track for smooth sliding motion
• Helps prevent drawer sagging, misalignment, and binding
• Reduces noise and scraping when opening or closing the drawer
• Restores proper engagement with the cabinet track for secure drawer operation

• Remove the drawer before replacing the glide; follow the appliance owner's instructions
• Inspect the cabinet track and adjacent parts; replace any damaged components for proper fit
• Use basic hand tools; avoid forcing parts to prevent breakage

This replacement glide helps a refrigerator or freezer drawer open and close smoothly and keeps the drawer aligned for reliable operation. It restores proper sliding action and reduces sticking or scraping. What it does

• Replaces a worn or broken drawer glide to restore smooth drawer movement
• Supports the drawer to prevent sagging and misalignment
• Helps reduce rubbing, sticking, and noisy operation during use
• Maintains proper drawer tracking so the drawer seats correctly

• Disconnect power to the appliance and remove food or contents from the drawer before starting
• Remove the drawer per your model's service instructions to access the glide
• Most installations are simple push-in or screw-replace procedures; keep fasteners from the original assembly

This glide restores smooth, aligned movement for a refrigerator or freezer drawer so the drawer opens and closes without sticking. Use it to replace a worn or broken glide and reduce scraping, binding, or uneven travel. What it does:

• Guides and supports the drawer so it tracks straight and slides smoothly.
• Replaces worn or damaged glides that cause drawers to stick, bind, or scrape.
• Helps prevent the drawer from coming off the track or shifting out of alignment.
• Reduces noise and uneven movement during opening and closing.

• Disconnect power (unplug the appliance) before servicing to avoid electrical hazards.
• Remove the drawer and any obstructing shelves per the OEM instructions to access the glide.
• Keep or replace original mounting screws; ensure the glide is oriented and seated correctly before tightening.
• Replace those parts to ensure a secure fit.

The Surface Element is an OEM part for Frigidaire electric ranges. It is the heating element located on the cooktop, responsible for providing the heat necessary for cooking. This component is essential for the proper functioning of your stove, ensuring consistent and reliable heating for various cooking tasks.

Causes of a bad surface element can include wear and tear from regular use, damage due to spills or overheating, or electrical failures such as a short circuit. A faulty surface element can result in uneven cooking or complete failure to heat.

Symptoms of a bad surface element include:

• Element not heating up
• Uneven heating or hot spots on the element
• Visible damage such as burns or cracks
• Element cycling on and off erratically

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Surface Element is an OEM part for Frigidaire ranges. The small surface element is responsible for providing direct heat to the cookware placed on the corresponding burner of the electric cooktop or range. This element is typically located underneath the glass surface of the cooktop or range, ensuring efficient and even heat distribution for cooking.

Symptoms of a failing Surface Element include:

• The element not heating up at all
• Heating unevenly or only partially
• Noticeable damage or blistering on the element itself
• The control switch not regulating the temperature properly

Causes of a bad surface element can include a burnt-out coil, a break in the element's continuity, or problems with the connection points such as corrosion or loosening. Regular wear and tear from cooking can also lead to degradation over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This cooktop top is the replacement surface panel that covers the range's burner area and restores a clean, stable cooking surface. Replaces damaged, dented, or worn tops to improve appearance and burner alignment. What it does:

• Covers and protects internal range components beneath the burners
• Provides a flat, stable surface for burner grates and cookware
• Helps maintain proper burner alignment and spacing
• Restores cosmetic appearance when original top is scratched, dented, or corroded

• One cooktop top / surface panel (single piece)

• Disconnect power (and gas if applicable) before beginning repair
• Remove burner grates, burner heads and control knobs as needed for access
• Support the panel during removal/installation; parts can be heavy—use two people if needed
• Retain and reuse existing mounting hardware unless replacements are specified

This mounting bracket secures internal components and panels so the appliance stays stable and aligned. Replacing a worn or broken bracket restores proper support and reduces rattling or misalignment. What it does:

• Provides structural support for internal panels, assemblies, or trim
• Holds components in correct position to prevent rubbing or vibration
• Stops movement that can cause noise, wear, or improper door/panel alignment
• Helps maintain safe operation by keeping parts securely fastened

• Disconnect power before starting any repair to avoid electrical shock
• Use basic hand tools; keep fasteners and orientation noted for reassembly
• Inspect surrounding clips, screws, and mounting points; replace any damaged hardware

This replacement refrigerator door handle provides a secure grip and restores safe, easy access to your refrigerator. It replaces a worn, cracked, or missing handle to improve function and appearance. What it does:

• Provides a sturdy grip to open and close the refrigerator door
• Replaces cracked, broken, loose, or missing handles and improves door usability
• Restores the cabinet's finished look by covering damaged or worn handle areas
• Helps maintain a proper seal by enabling correct door alignment when closed

• One refrigerator door handle

• Disconnect power to the appliance or unplug before working near electrical components
• Support the door while removing fasteners to prevent damage or injury
• Use the original screws and any mounting hardware;

This replacement part is a black element mounting clip used in ranges or wall ovens. This clip is used for surface elements on electric ranges and ovens. The clip itself connects the surface of the element to the support bracket which allows the stove to heat up. The user might need a new clip or clips if the heating element on the stove is loose, if the heating element is completely detached, or if the clip itself is bent or broken. This clip is black and made of sturdy metal that can withstand heat as well as strain on the clip itself. Installation of this clip is very simple as it just requires replacing the old one with a new one and making sure it is secure. Pliers might be required if the old clip is bent or stuck near or on the heating element. There are no special tools needed for this repair. This is an OEM part sourced directly from the manufacturer. It is sold individually. This part is compatible with machines from Frigidaire and other brands like Electrolux, Gibson, Kelvinator, Crosley, Westinghouse, and more.

This stainless steel cleaner restores and protects stainless surfaces, removing fingerprints, smudges and light soils to improve appearance and make routine cleaning easier. Safe for finished stainless when used as directed. What it does:

• Cleans away fingerprints, grease, and light residue from stainless surfaces
• Restores a streak-free shine and improves overall appearance
• Helps reduce visible smudges for easier routine maintenance
• Leaves a light protective finish that helps resist fingerprints between applications

• Read and follow the product label before use; test on an inconspicuous area first
• Apply to a soft cloth and wipe with the grain of the stainless; avoid abrasive pads
• Do not use on hot surfaces, painted finishes, or unsealed metals unless manufacturer approves
• Keep out of reach of children and avoid contact with eyes; if contact occurs, rinse thoroughly

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Size: 6-20 x 0.312 inch.

This is a replacement mounting screw used to secure panels and components in compatible Frigidaire appliances. It restores proper fit and helps prevent rattles, loose panels, and parts that shift during operation. What it does:

• Fastens trim, panels, brackets, or controls to the appliance frame
• Restores secure attachment to reduce vibration, noise, and movement
• Replaces stripped, missing, or corroded screws that prevent proper assembly
• Works wherever the OEM screw with this part number is specified

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging parts
• Keep removed hardware organized and compare parts to the old screw for correct fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.