Parts for Ge GTW680BSJ2WS: Top Panel & Lid Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This 10-32 hex head screw secures appliance panels and components where a small machine screw is required. It provides a durable, threaded fastening point for repair or reassembly. What it does:

• Fastens panels, brackets, and small components using a 10-32 machine thread
• Hex head accepts a 7/16" socket or wrench for positive torque application
• Replaces worn or damaged screws that cause loose or rattling parts
• Compatible with common metal-to-metal and tapped-hole connections

• One 10-32 hex head screw with 7/16" socket head

• Use the correct 7/16" socket or wrench to avoid rounding the head
• Thread engagement should match the appliance's threaded insert; do not force if resistance is felt
• Follow manufacturer service manual for torque specs and installation sequence
• Disconnect power and follow safety procedures before servicing the appliance

The Thermistor is an OEM part for GE washers. This thermistor monitors and regulates the temperature inside your GE washer during the different cycles.

The thermistor ensures accurate temperature sensing by measuring the temperature of the water or air inside the washer and sends this information to the control board, allowing it to adjust the heating elements or cooling mechanisms accordingly.

A bad thermistor can occur due to wear and tear, exposure to extreme temperatures, or electrical malfunctions. If you notice symptoms such as the washer not heating or cooling properly, error codes indicating a faulty thermistor, or inconsistent temperature readings, it may be time to replace the component.

Symptoms of a bad thermistor include:

• Washer not heating or cooling properly
• Error codes indicating a faulty thermistor
• Inconsistent temperature readings

Restore accurate temperature control by replacing the faulty thermistor with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

This factory-spec screw secures internal brackets, housings, and panels. Replacing a missing, stripped, or corroded fastener with the correct #6-32 size restores a tight, corrosion-resistant fit that keeps assemblies aligned and helps reduce vibration noise.

• Provides #6-32 machine-thread fastening for appliance components
• Helps maintain alignment and stability of brackets, housings, and panels
• Replaces stripped, rusted, or missing hardware that can cause looseness or rattling
• Stainless construction resists corrosion in high-moisture areas

• Disconnect power and, if applicable, shut off the water supply before servicing
• Start threads by hand to avoid cross-threading; use the correct driver for the head type
• Tighten snugly without overtightening, especially into plastic or thin sheet metal

The Lid Lock Striker is an OEM replacement part for GE washing machines. It is part of the lid lock system that allows the washer lid to securely lock during the wash and spin cycles.

Symptoms of a faulty lid lock striker include:

• Lid not securely locking during operation
• Error messages related to the lid lock system
• Inability to start the washer due to lid lock issues

A bad lid lock striker can be caused by normal wear and tear over time or damage due to accidental mishandling. If you notice that the lid is not securely locking or if the washer fails to start due to a lid lock error, it may be time to replace the old or damaged lid lock striker with this genuine OEM part.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This snap-in lid beauty plug restores the finished look of the washer lid and covers exposed screw holes for a cleaner appearance. It helps keep dirt and moisture out of the hinge/screw area while smoothing rough edges. What it does:

• Covers exposed holes or damaged trim on the washer lid to improve appearance.
• Helps block dirt and moisture from reaching screw heads and hinge openings.
• Prevents rough edges from catching clothing or skin.
• Useful when the original plug is missing, cracked, or worn.

• One lid beauty plug (snap-in cover).

• High-level DIY: usually presses into place—no special tools required.
• Always disconnect power to the appliance before working on or near electrical components.
• Avoid forcing the plug; align and press evenly to prevent breakage.
• If mounting area is damaged, replacement of surrounding trim may be required for a secure fit.

This lid front corner bumper cushions the washer lid and helps reduce noise, wear and abrupt contact when the lid closes. It restores smooth, quiet operation at the lid's front corner. What it does:

• Acts as a soft contact point between the lid and cabinet to dampen impact and vibration
• Prevents metal-on-metal contact that can cause chipping, scratching or rattling
• Helps keep the lid aligned for consistent closing and latching
• Commonly replaced when the lid squeaks, chips, or does not sit flush

• Lid front corner bumper

• Disconnect power to the appliance before beginning any work
• Typically installs by hand or with light pressure into the lid or cabinet corner; use gentle force to avoid damage
• Inspect surrounding area for cracks or wear and replace other damaged bumpers if needed

Center lid bumper cushions and aligns the washer lid to reduce noise and prevent metal-to-metal contact. Replace a worn or missing bumper to restore quieter, smoother lid closing and protect the lid edge and cabinet finish. What it does:

• Cushions the lid to reduce slamming, rattling and impact noise
• Helps the lid sit evenly to prevent rubbing or uneven closing
• Protects the lid edge and cabinet finish from contact damage
• Common symptoms: noisy or uneven lid closing, visible wear or missing bumper

• Unplug the appliance or disconnect power before servicing.
• Typically snaps or presses into a mounting boss under the lid; remove the old bumper before installing the new one.
• Use a non-marring tool or gloved hand to avoid scratching the lid; inspect surrounding mounting area for damage.

The Lid Lever Arm is an OEM part for GE washing machines. This component is crucial for the proper functioning of the washer's lid mechanism, ensuring that the lid locks securely during operation and allows for safe and efficient washing cycles.

Over time, the lid lever arm can become worn out or damaged due to regular use, improper handling, or mechanical failure. Causes of a bad lid lever arm include physical damage, wear and tear from repeated use, or issues with the linkage that connects it to the locking mechanism.

Symptoms of a bad lid lever arm include:

• The washer lid not locking properly
• The washing machine not starting or pausing unexpectedly
• Error codes related to lid lock issues
• The lid feeling loose or misaligned

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Lock Service Kit is an OEM part for GE washing machines. This kit includes the components necessary to ensure that the washer lid remains securely locked during operation, preventing the lid from being opened when the washer is in use. This safety feature is crucial for top-load washers, ensuring safe and efficient operation by preventing access to the washer drum during cycles.

The kit includes:

• Lid Lock & Harness Assembly
• White Bezel
• Gray Bezel
• White Strike
• Gray Strike

Common causes of a malfunctioning lid lock include wear over time, damage to the lock mechanism, or electrical issues that prevent the lock from engaging or disengaging properly. Exposure to moisture and constant use can also affect the performance of the lid lock system.

Symptoms of a bad lid lock include:

• The washer not starting or advancing in the cycle
• Error codes related to the lid lock
• The lid not locking or unlocking as expected
• The washer stopping mid-cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Glass Frame Assembly is an OEM part for GE washing machines. It serves as both a protective barrier and a see-through lid on the washing machine. The glass frame allows users to monitor wash loads without having to open the door and risk water spillage. 

Symptoms of a bad glass frame assembly include:

• Cracks or chips in the glass that compromise strength and viewing ability
• Warping, bending, or other distortions of the frame itself
• Binding, sticking, or troublesome opening/closing of the lid 

Causes of failure are typically impacts or accidental mishandling that result in damage over time. Glass can crack or frames become misshapen from repeated use and closing of the heavy lid.

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Lock Service Kit is an OEM part for GE washing machines. This kit includes the components necessary to ensure that the washer lid remains securely locked during operation, preventing the lid from being opened when the washer is in use. This safety feature is crucial for top-load washers, ensuring safe and efficient operation by preventing access to the washer drum during cycles.

The kit includes:

• Lid Lock & Harness Assembly
• White Bezel
• Gray Bezel
• White Strike
• Gray Strike

Common causes of a malfunctioning lid lock include wear over time, damage to the lock mechanism, or electrical issues that prevent the lock from engaging or disengaging properly. Exposure to moisture and constant use can also affect the performance of the lid lock system.

Symptoms of a bad lid lock include:

• The washer not starting or advancing in the cycle
• Error codes related to the lid lock
• The lid not locking or unlocking as expected
• The washer stopping mid-cycle

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This bleach cup is the injection-style dispenser that holds and releases liquid bleach during a wash cycle, helping deliver bleach where needed for stain removal and whitening. It fits into the washer's dispenser area to control bleach flow. What it does:

• Holds liquid bleach until the washer adds it at the correct cycle stage
• Directs bleach into the wash water to help remove stains and brighten fabrics
• Commonly replaced when the cup is cracked, broken, or no longer seats securely
• Helps prevent leaks or uneven dispensing caused by damaged or missing cups

• One bleach cup

• Designed for a snap-in or press-fit installation; confirm alignment before seating
• Remove power to the appliance before accessing the dispenser area
• Inspect surrounding dispenser housing for damage and clean residue before installing

This plate shower dispenser directs wash water over dishes for improved cleaning coverage in compatible dishwashers. Replace a cracked or clogged dispenser to restore proper spray distribution and help reduce spotting and food residue. What it does:

• Channels pressurized wash water to targeted plate and dish areas for better cleaning coverage
• Helps maintain consistent spray pattern to reach upper and lower rack surfaces
• Can prevent water from bypassing dishes when cracked or obstructed
• Common symptom: reduced cleaning performance or visible damage/cracks on the dispenser

• One plate shower dispenser

• Disconnect power and water supply to the appliance before starting any repair
• Inspect mounting tabs and seals; replace damaged clips or gaskets as needed for a secure fit
• Handle plastic parts gently to avoid cracks; ensure proper alignment before securing

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement siphon cap fits the washer's dispenser assembly. The insert creates the siphon action that empties the additive cup during the rinse cycle, helping prevent standing liquid and residue so liquid additives dispense as intended.

• Forms a siphon in the dispenser cup so liquids empty at the proper time
• Helps reduce standing water and residue buildup in the dispenser
• A worn or missing cap can contribute to odors or buildup in the dispenser area

• Unplug the washer and turn off water before servicing
• Remove the dispenser drawer or cup and lift out the old siphon cap
• Clean the dispenser area; press the new cap in firmly so it seats evenly
• Reinstall the drawer/cup and run a rinse to ensure proper dispensing

The Detergent Dispenser Assembly is an OEM part for GE washers. It acts as the gateway through which detergent is added and released during cycles. This assembly contains the dispenser drawer. 

Causes of a bad dispenser assembly include mineral or soap buildup blocking valves, cracks in the drawer allowing leaks, or damaged inlet and outlet components.

Symptoms of a bad dispenser assembly are:

• Improper or incomplete dispensing of detergent 
• Residual detergent left in the drawer after cycles
• Leaks or puddles around the dispenser area  
• The drawer fails to open or close fully

Replace yours today with this genuine GE assembly to restore proper detergent dosing for effective cleaning performance. This OEM GE replacement is also compatible with Hotpoint, RCA, and some Kenmore models.

The Lid Hinge is an OEM part for GE washers. It provides the mounting and fulcrum point for the washer lid, allowing smooth movement between open and closed positions. The sturdy hinge construction is designed to withstand repetitive use over many cycles.

Causes of a bad lid hinge can include fatigue from extended use, damage or loosening of mounting screws, or impact dents deforming the metal.

Symptoms include:

• Looseness, wobbling, or sagging of the washer lid 
• Difficulty fully opening or closing the lid securely
• Noise or squeaking emitted from the hinge area
• Physical deformation reducing the proper range of motion

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Replacing a worn or faulty lid hinge ensures comfortable, predictable lid movement for years to come.
 

A single replacement screw used to secure the lid hinge on top-load washers. Replaces a worn or missing hinge fastener so the lid stays aligned and operates smoothly. What it does

• Secures the lid hinge assembly to the washer cabinet or lid
• Restores proper lid alignment and reduces wobble or sagging
• Helps stop the lid from shifting, binding, or making noise when opened/closed
• Used when original screw is missing, stripped, or damaged

• One lid hinge screw

• Disconnect power and water supply before working on the washer
• Support the lid and hinge assembly while removing and installing the screw to prevent injury or damage
• Use the correct screwdriver or bit to avoid stripping the screw head

The Lid Lock Wiring Harness is an OEM part for GE washing machines. It connects the lid lock mechanism to the washing machine’s control board, ensuring proper communication and functionality. This wiring harness is crucial for the safe operation of the washer, as it ensures the lid remains locked during certain cycles to prevent accidental openings and maintain safety.

You should replace the lid lock wiring harness if it becomes faulty. Causes of a bad wiring harness can include regular wear and tear, electrical faults, or damage from impacts or pinching. A damaged wiring harness can lead to communication errors between the lid lock and control board, resulting in improper functioning of the lid lock mechanism.

Symptoms of a bad lid lock wiring harness include:

• The washing machine not starting or stopping mid-cycle
• The lid not locking or unlocking properly
• Error codes related to the lid lock mechanism
• The washer not responding to control inputs

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This 10-32 machine screw fastens small appliance components and replacement assemblies, restoring secure mounting and reliable electrical or panel connections. Its length fits common cabinet, control, and bracket attachments. What it does

• Secures control boards, panels, brackets, and grounding tabs using a 10-32 machine thread
• Replaces stripped or missing mounting screws that allow panels or parts to rattle or shift
• Helps restore stable electrical connections where a threaded fastener is required
• Works where a 1.31 in (approx. 1-5/16 in) long 10-32 screw is specified

• Power off and unplug the appliance before beginning any repair
• Match thread size and length to the original screw; do not force a wrong-size fastener
• Start threads by hand to avoid cross-threading; tighten securely but do not overtighten
• Use appropriate tools and wear eye protection when working on metal assemblies

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This is a self-tapping Plastite screw with a hex washer head and a 5/8 in. length that secures plastic and thin-sheet components. Use it to replace missing or damaged mounting screws for a snug, reliable fit. What it does:

• Forms threads in plastic (Plastite style) to fasten panels, brackets, and trims.
• Hex washer head provides a larger bearing surface for better holding power.
• Replaces stripped, corroded, or missing screws to stop loose or rattling parts.
• Works where a self-tapping screw is required for secure mounting without a separate nut.

• Use the correct hex/nut driver and a properly fitting bit to avoid stripping the head.
• Hand-start the screw and drive straight to prevent cross-threading; stop when snug—do not overtighten into plastic.
• Unplug the appliance or shut off power before disassembling or working near electrical components.
• Replace with the same screw type and size to maintain proper fit and function.

The Water Inlet Valve Seal is an OEM part for GE washing machines, designed to ensure a watertight seal around the water inlet valve. This part helps prevent leaks by sealing the connection between the water inlet valve and the washing machine's internal tubing. 

Causes of a bad water inlet valve seal include normal wear and tear, exposure to hard water minerals that can erode the seal, and improper installation that may strain or damage the seal.

Symptoms of a bad Water Inlet Valve Seal include:

• Water leaking from the back or underside of the washing machine
• Visible signs of wear or damage to the seal
• Unexplained increase in water usage or utility bills, which may indicate a slow leak

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Water Inlet Valve is an OEM part for GE washing machines. It is responsible for controlling the entry of hot and cold water into the washing machine. This valve opens and closes at the appropriate times during the wash cycle to allow water to enter based on the selected temperature and wash settings.

Causes of a bad water inlet valve include mineral deposits from hard water, which can block the valve, and wear and tear from regular use, which can cause the valve to fail mechanically or electronically. Additionally, if the screens that filter the water before it enters the valve become clogged, water flow can be restricted, affecting the washing machine’s performance.

Symptoms of a malfunctioning water inlet valve include:

• The machine not filling with water.
• Water entering the machine slowly.
• Water leaking around the valve area.
• A noisy valve during operation.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This water valve harness is a direct-replacement wire harness that connects the refrigerator's water valve to the control and power source, restoring proper electrical connection for water dispensing and ice maker fill functions. What it does:

• Provides the electrical connections between the fridge control and the water inlet/solenoid valve
• Restores power/signal delivery to the water valve so the dispenser and icemaker can fill
• Commonly used when the valve won't actuate or water flow is intermittent
• Helps replace damaged, corroded, or broken wiring/connectors that prevent reliable operation

• Disconnect power and turn off the water supply before beginning work
• Match connector shapes and pin counts; do not force connectors or bend pins
• Inspect mating connectors and valve terminals for corrosion; replace if needed
• Secure harness away from sharp edges and moving parts; test dispenser/icemaker after reassembly

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.