Trimmer Plus Trimmer

This is an extension boom and flex shaft assembly that is used in pole pruners and string trimmers. It is made to offer extra extensions so the pruner or trimmer can be used on items farther away from the user. It adds additional reach to make yard and garden tasks easier. The tube comes with an internal flexible drive shaft. It arrives to the user in a pre-assembled state and is ready to be installed. This shaft assembly can be used to replace a broken part or purchased to add reach to a pruner or trimmer that didn't come with one.This boom and flex shaft assembly requires no tools to be installed. Make sure the equipment it will be installed on is turned off, and the spark plug wire has been disconnected. Access the shaft and remove the broken boom and flex shaft assembly. The new replacement part can be installed by hand.This is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The extension boom and flex shaft assembly is designed to be used with string trimmers and pole pruners manufactured by MTD and Ryobi.

The gearbox assembly is found in tillers and is where the gears are housed that supply the drive and torque for the unit. The gearbox assembly is designed to provide protection for the gears and the other internal components, which are responsible for transferring energy to increase torque and control speed. Although it is made of durable materials, it may become worn or damaged over time and require a replacement. This genuine OEM gearbox assembly is produced to exact manufacturer standards and made to be used in compatible machines from Yard-Man, Ryobi, Yard Machines, Bolens, Cub Cadet, and MTD. The gearbox assembly is sold as an individual assembly and comes ready to install with the four screws required for installation. Be sure to wear gloves and disconnect the power from the tiller before performing any repairs. Allow the unit to cool completely and follow the diagram to ensure that the replacement part fits exactly. This assembly will require a screwdriver and wrench set to replace.

This replacement part is an oil tank assembly. This is a genuine replacement part made by MTD. This part is responsible for holding the oil or fuel that is needed for many types of machines that run using this type of engine. A new oil tank assembly might be needed if the current one is damaged or broken in any way. This can be due to normal wear and tear after years of use. If the tank is cracked it may be leaking oil. If this is the case it is recommended that it be replaced as soon as possible. The repair should be fairly simple and only require common household tools. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a replacement gear box assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part is intended to replace a defective, broken, or worn out gear box assembly on various models of outdoor small engine power equipment. The gear box assembly, also referred to as the transmission, allows equipment to run smoothly and transition through gears. Over time, the gear box may become worn or faulty, preventing the equipment from functioning properly. Proper tools are required to replace this part. It is always recommended that the appropriate safety precautions are adhered to when attempting to fix any power tools or machinery. When working on or near an engine, ensure the equipment is turned off and completely cooled down before starting any repairs. For more accurate information on how and where to install this gear box assembly, the appropriate owner's manual and included diagrams should be referenced.As an authentic replacement part, this gear box assembly is suitable for use on several different models of string trimmers and pole pruners manufactured by MTD, Troy-Bilt, and Cub Cadet. This is a genuine part made of high-quality, durable, non-corrosive materials and is sold individually.

This tine assembly is a genuine MTD part, sold individually. This tine assembly can be used as a replacement part in a tiller. The purpose of the tine assembly in a tiller is to bore into the soil and loosen up packed dirt so that plants and greenery can be kept healthy and verdant.If the tines are dented, cracked, warped, eroded, or otherwise damaged to the point that they cannot effectively bore into the soil and serve their function, the tine assembly should be removed and replaced by this genuine OEM replacement part before using the tiller again.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This tine assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Troy-Bilt, Cub Cadet, and Yard Machines.

This tine assembly is a genuine MTD part, sold individually. This tine assembly can be used as a replacement part in a tiller or a string trimmer. The purpose of the tine assembly in a tiller or a string trimmer is to provide the appliance with the proper blades to cut through and loosen soil in order to keep the lawn of the operator healthy.The tine assembly in a tiller or a string trimmer might need to be replaced at some point within the standard lifespan of the outdoor appliance. This could occur if the tine assembly has been punctured, warped, dented, cracked, or eroded to the point that the tines are no longer as functional as they once were. If this is the case, the tine assembly should be removed and replaced by this genuine OEM replacement part before using the tiller or the string trimmer again.This is a genuine OEM replacement part sourced directly from the manufacturer. It is sold individually. This tine assembly is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, and Yard Man.

This screw and nuts set is a genuine MTD part, sold individually. This screw and nuts set can be used as a replacement part in a string trimmer. This set provides a variety of screws and nuts which serve as fastening components within the string trimmer.The screw and nuts set in a string trimmer might have to be ordered as a complete replacement part if one or more screws or nuts in the string trimmer has been lost, misplaced, or damaged. If this occurs, the screw and nuts set should be ordered as a genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This screw and nuts set is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Bolens, and Yard Man.

Trimmers have a shield assembly that protects the user from flying debris while the trimmer string is in operation. If this assembly cracks or falls off, the trimmer should not be operated until a new on is installed. Over time, the sun's heat may cause the plastic to crack, ultimately leading to the shield falling off. Safety is an important factor when operating lawn and garden equipment. Routine inspections of all equipment will reveal if any of the safety components of the machines are broken or missing.This shield assembly is an authentic OEM replacement part sourced directly from the manufacturer. Before installing this part, make sure the spark plug is removed and wear safety gloves. After removing the damaged shield, this shield should be installed using the screws from the one taken off the trimmer. This shield assembly is a black molded plastic part that is sold individually. It does not come with screws. It is designed for use with trimmers manufactured by Troy-Bilt and Craftsman.

This replacement part is a gearbox intended for use in grass trimmers. This is a genuine replacement part made by MTD. Gearboxes connect the main handle of the appliance to the rotating blade attachment. It is important that this part is secure as the blade cutter can be dangerous if loose.A new gearbox might be needed if the current one is broken or damaged in any way. It is not unusual for this part to require replacement after years of normal use as it's easy for the gearbox to become stripped down. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. For more detailed instructions on how to replace this specific part, please reference the user guide or manual for the appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with grass trimmers made by MTD.

This boom is a genuine MTD part. It is a replacement part for string trimmers, leaf blowers, and other handheld garden appliances. It is part of the lower housing assembly.Replacing the lower housing boom is not an advanced repair, but it requires disassembly of most of the leaf blower, including the blower cover, spark plug, fan blade, and more. Always take proper safety precautions with complex repairs. This boom is a genuine OEM part sourced directly from the manufacturer. It is designed to be compatible with machines made by Click Link, Craftsman, Cub Cadet, McCulloch, Ryobi, Trimmer Plus, Yard Machines, and Yard-Man.

This part is a replacement drive belt. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace broken, snapped, or defective drive belts in a variety of snow blower models. The drive belt is what helps to power the snow blower and is critical to proper equipment functionality. Belts are subject to significant amounts of wear and tear and must be replaced if snapped, worn, brittle, or otherwise rendered ineffective. When working on or near an engine, it's important to make sure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this drive belt, the appropriate owner's manual and equipment diagrams should be utilized.As an authentic replacement part, this drive belt is suitable for use on several different models of snow blowers manufactured by MTD, Craftsman, and other brands. This is a genuine part made of high-quality, durable materials and is sold individually.

This part is a 4-tooth brush blade that is used on weed trimmers. The purpose of a brush blade is to cut brush and weeds. This component attaches to the gearbox.A new 4-tooth brush blade may be needed if the weed trimmer is not properly cutting brush or grass. If this component is cracked, broken, dented, or otherwise damaged in any way, it will need to be replaced. Use extreme care when handling any moving components on outdoor power equipment and never attempt care or maintenance on a machine that is powered on. Remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment.This 4-tooth brush blade is a genuine MTD part. It is sold individually. This particular 4-tooth brush blade is compatible with weed trimmers that are manufactured by MTD, Craftsman, and Ryobi.

This replacement part is a concentrator nzle and is intended for use in different types of lawn equipment. This is a genuine replacement part made by MTD. Concentrator nzles are an important part of many machines and are responsible for directing the airflow that is coming out. This particular nzle is typically found in leaf blowers and helps the user gain a more accurate position when trying to clear leaves and other debris. A new concentrator nzle might be needed if the current one is damaged or missing. If the current one is missing the user might have trouble clearing debris as the airflow might not be as concentrated to one area. This replacement or repair should be fairly simple and should not require any major tools. Most nzles are able to slide off and clip on. This nzle is a genuine OEM replacement part. This part is sourced directly from the manufacturer to ensure a proper fit and is sold individually.

This is a trimmer head used with string trimmers, weed wackers, and edgers. When in use, it rotates, cutting grass. If the trimmer head stops rotating or cutting grass, it is time to order a replacement part. In order to complete the replacement process for trimmer heads, the user will need to pry the trimmer head off of the trimmer. Use a flathead screwdriver to loosen it. After pulling the old trimmer head off the nut on the bottom of the shaft, insert this replacement head onto the trimmer shaft.This trimmer head is a genuine OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with brands such as Craftsman, Cub Cadet, Ryobi, Troy-Bilt, Yard Machines, MTD, Bolens, and Yard-Man.