Troy-Bilt Lawn Mower Parts

The discharge chute assembly is located on the deck of the lawnmower. It is made out of durable plastic but can be damaged by impacts. It also can experience wear and tear that make it break or become weaker. If the discharge chute is broken or damaged, it will need to be replaced. Usually, the discharge chute will have visual wear or damage that alert a user to replace the part.The replacement of a discharge chute assembly is simple and takes only a few minutes. A socket set will be needed to go through the process. The original discharge chute assembly can be removed using the socket set. Replace it with the new replacement part. Before replacing the parts, make sure the lawnmower is powered off, and the spark plug wire has been disconnected.This is an authentic OEM replacement part that is sourced directly from the manufacturer. The part is sold as an individual unit. This discharge chute assembly is made for use with lawnmowers manufactured by Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Yard-Man, and MasterCut.

This carriage bolt is a fastener with a flat tip and a round head with threading along the shank. Also known as coach bolts and plow bolts, the item can be used with many types of lawn and garden equipment. This is a 5/16 carriage bolt that resists turning after the bolt has been tightened. Wear and tear or impact can cause damage to a carriage bolt and lead to the need to replace them.Removing a carriage bolt requires twisting the nut loose from the end of the bolt and then hitting the nut with a hammer. This will begin to move the shoulder out of the lawn equipment. Continue the process until the bolt is loose enough to remove. Installing a new carriage bolt simply requires sliding the bolt into the hole, adding the nut, and tightening things up.This carriage bolt is designed for use with Craftsman, MasterCut, Toro, Yard-Man, Cub Cadet, Montgomery Wards, Ryobi, Huskee, Troy-Bilt, MTD, and Yard Machines lawn and garden equipment. It can be used with lawnmowers, chainsaws, snowblowers, edgers, and tillers. This is a genuine OEM product sourced directly from the manufacturer as an individual component.

The shoulder screw is used in places where a spacer or bearing surface is needed, since the top half of the screw is unthreaded. These fasteners are often used for guides, pivot points, mounting pins, axles, and even a shaft for bearings and bushings in various MTD engines. With regular use, the screws can wear down or be lost. Always repair the missing hardware promptly with genuine OEM replacements. Disengage the spark plug and wear gloves when performing work on engines for safety. This genuine OEM replacement shoulder screw has been designed to be compatible with machines from MTD, Troy-Bilt, Yard-Man, Yard Machines, Bolens, Cub Cadet, and Craftsman. It can be used for multiple applications and in multiple locations in different models of lawnmowers, tractors, and chippers that use the screw in various applications. Check your parts diagrams for the exact location and use of these screws before ordering. This is sold as an individual unit; order multiple quantities as needed.

This handle grip part is used on many kinds of lawn and garden equipment that is pushed or otherwise moved around a yard. The handle grips are made out of flexible rubber and are used on the two handles. The purpose of the handle grip is to offer a more secure grip on the power tool and lessen the feel of vibrations.Over time, one or both of the handle grips can start to experience wear. Sometimes, the grips will become damaged or broken. If the grips are very damaged, they may come off of the machinery. There is no need to use tools to replace the handle grip on yard equipment. The old part just needs to be removed from the tool so that the new component can be slipped on. Wear a pair of work gloves to make the process easier.This is a genuine OEM handle grip replacement that is sourced directly from the manufacturer. It is sold individually. The part is compatible with lawnmowers, snowblowers, tillers, and chainsaws created by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.

This front roller is used as a replacement part on lawnmowers from major lawn and garden manufacturers. It attaches to the lawn mower's front deck to keep the mower level with the surface of the yard. If the roller is damaged or missing, the lawnmower deck will be unlevel, which can cause various problems. If the front roller is too low, the mower can scalp the lawn leaving bare spots. These spots will turn brown and have to be reseeded to restore the grass. If the front is too high, the grass will be cut unevenly.If the lawnmower is cutting but not cutting evenly or is leaving bald areas, the front roller should be inspected and replaced as needed. Normal wear and tear may have loosened it, or it may be damaged from hitting rocks and sticks in the yard. Replacement is simple and can normally be completed in less than half an hour. Make sure the lawnmower is cool and parked on a level surface. Pliers are needed to remove and replace the roller.This front roller is a genuine OEM part sourced directly from the manufacturer. It is sold as an individual unit. The front roller is made compatible with lawnmowers manufactured by Cub Cadet, Huskee, MTD, and Troy-Bilt.

This genuine OEM replacement part is a flange bearing designed to be used with a wide range of lawn tractors. A bearing is a mechanical part made to restrict movement and prevent other parts from shifting about in the tractor. This is a flange bearing, referring to its particular shape. The bearing slides into place while the flange creates an added layer of protection around the connection. While restricting motion, bearings experience a lot of friction. After a long period, a bearing may eventually begin to wear away and other parts may start to feel loose or pull apart. This can cause more widespread damage in a lawn tractor, such as a broken suspension or disconnected lower deck. The difficulty of this repair will depend largely on where the flange bearing that needs replacing is located. The odds are that any repair will require a socket wrench set, a screwdriver, and a pair of pliers to access any flange bearing. This replacement flange bearing is sourced from its original manufacturer and will fit tractors made by Ryobi, MTD, Bolens, Troy-Bilt, Cub Cadet, Yard Man, and Yard Machines. This part does not include any additional hardware.

This lift cable is designed for use with many lawnmowers and snowblowers to ensure that the gears run smoothly while using the equipment. The lift cable is made of durable materials but has delicate connectors on each end which may eventually wear out. When the connectors or cables are damaged, the part will need to be replaced. This component is important since it helps control how fast the blades or other parts of the tool can operate. If the cable breaks, the tool may not start.If the lift cable has gone bad, is worn out, or is damaged, replacement is needed. There will be no need to use tools during the process, but work gloves can be helpful. The lift cable can be untwisted from the housing and removed from the tool. Take the new component and place it in the same location. Make sure to reassemble any additional parts before useThis is an authentic OEM replacement part that is directly sourced from the manufacturer. It is sold as an individual component. The lift cable is made to fit lawnmowers and snowblowers manufactured by Craftsman, Toro, Cub Cadet, Troy-Bilt, MTD, Huskee, Montgomery Wards, and Yard-Man.