Parts for Maytag MMV5208WS1: 05 - Turntable Parts

This inlet cover protects and conceals the appliance's inlet area, keeping wiring and connections secure and helping prevent debris from entering. It restores a clean, safe inlet opening and supports proper component alignment. What it does:

• Shields the inlet opening and nearby connections from dust and debris
• Holds inlet components in position to reduce movement and wear
• Helps prevent snagging or accidental contact with inlet wiring or fittings
• Visible damage or a loose/misaligned cover can expose connections and lead to leaks or electrical issues

• One inlet cover

• Disconnect power and shut off water supply before beginning work
• Remove the appropriate access panel or trim to reach the inlet area
• Replace cover, securing with the original screws or clips; do not overtighten
• Inspect nearby gaskets, fittings and wiring while replacing the cover

This support secures and stabilizes a mating component inside your appliance, helping restore proper alignment and fit. Replace a damaged or missing support to stop wobble, sagging, or misalignment.

• Provides structural backing to keep the attached part level and in place
• Helps eliminate rattling, shifting, or uneven gaps
• Replace if cracked, deformed, or missing
• Symptoms can include loose or sagging parts, poor alignment, or difficulty reinstalling shelves/panels

• Disconnect power (and shut off water, if applicable) before service
• Remove the affected shelf/drawer/panel to access the support
• Transfer and reuse any model-specific fasteners or clips
• Seat the new support fully and check alignment before reassembly

This factory support stabilizes and positions its mating assembly so it stays secure and aligned during use. Replacing a worn or broken support helps restore proper fit and prevents looseness or shifting that can affect performance. What it does

• Provides structural support and correct positioning for the related assembly
• Helps prevent wobble, sagging, rattling, or misalignment
• Typical failure signs: visible cracks, broken/missing tabs, or a loose fit
• Can help resolve components not staying in place or moving unexpectedly

• 1 support

• Disconnect power to the appliance before servicing
• Access the support location and note the original orientation
• Transfer and reuse any original mounting hardware your model uses
• Seat the new support fully and verify a secure fit before restoring power

This support is a factory mounting piece that secures and aligns its mating component inside the appliance. Replacing a worn or broken support restores proper fit, stability, and smooth operation of the associated assembly.

• Provides structural support and accurate positioning for the designated part
• Helps prevent sagging, looseness, and vibration
• Maintains alignment so components latch/seat correctly
• Typical failure signs: cracked or missing support, rattling, misalignment, or parts that won't stay in place

• Disconnect power before servicing; also shut off the water supply
• Note the original orientation; transfer any screws, clips, or spacers from the old support
• Install without overtightening to avoid damage; secure fit of the supported component after installation

This support mounting bracket secures internal components and helps keep the appliance cabinet and panels aligned for reliable operation. It restores proper fit and prevents movement that can cause noise or wear. What it does:

• Provides structural support for the appliance cabinet or internal assemblies
• Keeps panels and components aligned to reduce vibration and rattling
• Helps prevent sagging or misalignment that can cause doors or panels to bind
• Supports stable operation after other hardware or clips fail

• Basic hand tools required; disconnect power before starting any repair
• Inspect surrounding clips and fasteners and replace any that are damaged
• Tighten to OEM torque ranges if specified; avoid over-tightening to prevent damage

The Motor-Turn is an OEM part compatible with Whirlpool microwaves. Located inside the microwave cavity on the turntable mechanism, the motor-turn contains the turntable motor and drive components. 

Causes of a bad motor-turn can include a faulty motor, worn gears or pulleys, or broken turntable shaft. 

Symptoms of a bad motor-turn include:

• The turntable not rotating or rotating unevenly
• Loud grinding noises emanating from inside the cavity
• Burning or uneven cooking of foods
• Traces of sparks near the turntable mechanism

This OEM Whirlpool replacement motor-turn assembly is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore microwaves. 

Comes with 4 supports. Color: chrome.

This replacement mounting plate secures internal components so the appliance operates quietly and stays aligned. Replacing a damaged or bent plate helps stop rattling, prevent part movement, and restore proper fit between adjoining parts. What it does:

• Provides a stable mounting surface for nearby components and fasteners
• Prevents parts from shifting or vibrating during operation
• Helps eliminate rattling or noise caused by a loose or bent plate
• Restores correct alignment where the original plate was damaged or deformed

• One replacement plate

• Disconnect power (unplug appliance or turn off circuit) before starting any repair
• Wear gloves and eye protection; edges may be sharp
• Use correct fasteners and torque to avoid bending the new plate;