Parts for Frigidaire FFTA1233S21: Unit Parts

This air filter screens the air moving through your appliance's ventilation system, capturing odors and fine particles. Replacing a clogged or damaged filter helps maintain proper airflow so the unit vents and circulates air as designed. What it does:

• Captures odors and airborne particles as air passes through the unit
• Helps maintain proper airflow/venting performance
• Reduces debris buildup on internal components
• Common signs it's due: persistent odors, reduced airflow/venting, a visibly dirty or damaged filter

• 1 air filter

• Disconnect power and allow hot surfaces to cool before servicing
• Open the filter access panel or grille and note the filter's orientation
• Remove the old filter; seat the new filter fully and close the cover
• Restore power and verify proper airflow

This blower wheel circulates air through the dryer drum and venting system to maintain proper airflow for efficient drying. Replaces a worn or damaged wheel to help restore drying performance and reduce unusual noises. What it does:

• Channels air from the dryer motor through the drum and exhaust system
• Helps maintain consistent drum airflow for faster, more even drying
• Can reduce or stop rattling, scraping, or thumping noises caused by a broken or imbalanced wheel
• Restores proper vent pressure that can prevent extended dry cycles

• Disconnect power to the appliance before beginning any repair.
• Access usually requires removing the dryer front or rear panel; keep fasteners organized.
• Inspect the motor shaft, mounting clip, and housing for wear; replace damaged hardware as needed.

This base is the lower cabinet support that stabilizes and secures the appliance's bottom panels for proper alignment and operation. It restores a level, secure foundation for safe, quiet performance. What it does:

• Supports and evenly distributes the appliance weight across the cabinet bottom
• Secures lower trim and panels to prevent gaps and misalignment
• Helps reduce rocking, vibration, and floor contact noise when damaged or worn
• Maintains correct clearance at the appliance bottom for proper airflow and fit

• Disconnect power and water before starting any repair.
• Use two people or proper lifting tools to tilt or lift the appliance safely.
• Basic hand tools required; follow the appliance service manual for panel removal and reinstallation.

This fastener kit supplies the assorted screws and clips used to secure panels and components on compatible Frigidaire appliances, helping restore proper fit and stop loose or rattling parts. Ideal for repairs where original mounting hardware is missing or damaged. What it does:

• Replaces worn, missing or damaged mounting hardware so panels, brackets and trim stay secure
• Helps eliminate vibration noise and loose-fitting parts that cause rattling
• Restores correct alignment for doors, panels or internal assemblies that use small fasteners
• Provides the specific fasteners needed for the factory-replacement process

• Basic hand tools (screwdrivers, nut drivers) are typically required; refer to your model's service manual for exact fastener locations and torque
• Turn off power and disconnect the appliance before starting any repair to avoid shock or injury
• Handle small parts carefully and keep them away from children and pets

This electronic PC board controls a refrigerator's user interface and operating functions, restoring normal control and display behavior when the original board fails. It replaces the fridge's main control electronics to help resume normal operation. What it does

• Manages user inputs, electronic controls, and display signals so the appliance responds correctly to settings
• Controls compressor, defrost, and fan signals to regulate cooling cycles
• Helps prevent erratic operation caused by failed or damaged control circuitry
• Common symptom linkage: unresponsive control panel, blank or incorrect display, or intermittent cycling

• Disconnect power before servicing to avoid electric shock; confirm power is off with a meter
• Handle the board by its edges and avoid static discharge; use ESD protection if available
• Follow OEM service manual for removal and reinstallation steps; note connector locations and wire routing

This electronic control is the main console board that manages oven functions and user controls, restoring responsive buttons and cycle logic for accurate cooking. It replaces a failed or unresponsive control assembly to return normal operation. What it does:

• Receives input from the touchpad/knobs and runs the oven's timing, temperature and bake/broil sequences
• Manages display readouts and on/off status for cycles and timers
• Stops or prevents cycles when the control is faulty (symptoms: blank display, unresponsive controls, incorrect cycle behavior)
• Works with safety interlocks and sensors to regulate heating elements and maintain set temperatures

• One electronic control board

• Disconnect power at the breaker or unplug the appliance before starting
• Handle the board carefully and avoid static discharge; use ESD precautions if available
• Remove the console/back panel screws to access and swap the control assembly; keep hardware for reinstallation
• After install, restore power and verify all functions and displays operate normally

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

A handheld replacement remote that restores convenient, wireless control of your appliance's basic functions — power, mode, temperature and fan settings — without needing to access the control panel directly. What it does:

• Sends wireless commands to the appliance to change power, temperature, fan speed and operating mode
• Replaces a lost, damaged or non-working remote to restore remote operation
• Helps diagnose remote-related control issues by providing a working transmitter for testing
• Works with the appliance's front-panel receiver; operation depends on line-of-sight and fresh batteries

• Install fresh batteries before first use and follow the appliance manual to pair or sync if required
• Point remote at the appliance's IR/receiver window and test functions at close range first
• Keep remote dry and avoid dropping; handle electronic parts with care
• Dispose of batteries and packaging according to local regulations

This power cord connects your appliance to household power, restoring electrical supply so the unit can run. It's a direct-fit style cord designed to replace a damaged or missing power lead. What it does:

• Provides the main electrical connection from the wall outlet to the appliance
• Replaces frayed, cut, or burned cords that can cause shorts or loss of power
• Helps resolve symptoms such as the appliance not powering on or intermittent power
• Restores a secure plug and strain relief for safe operation

• Always disconnect power at the breaker or unplug the appliance before installation
• Route the cord and secure any strain relief per the appliance's wiring diagram