Parts for Kenmore 253.77085512 (25377085512, 253 77085512): Unit Parts

Screens air and captures odors and particles in your room air conditioner. Replace when clogged to maintain proper airflow. Confirm fit with your model.

Replacement louver for room air conditioners. Directs airflow and completes front panel appearance. Order now if yours is cracked, broken, or missing.

This is a centrifugal blower wheel that mounts on the fan motor shaft inside the air conditioner to circulate air through the unit. It draws air across the evaporator coil and pushes conditioned air into the room. Replace this blower wheel if you notice reduced airflow, unusual rattling or vibrating noises, or if the wheel's fins are cracked, broken, or clogged with debris that cannot be cleaned.

Fix weak airflow or loud operation in your air conditioner with this fan blade. Common repair for units that run but don't cool effectively.

This base is the lower cabinet support that stabilizes and secures the appliance's bottom panels for proper alignment and operation. It restores a level, secure foundation for safe, quiet performance. What it does:

• Supports and evenly distributes the appliance weight across the cabinet bottom
• Secures lower trim and panels to prevent gaps and misalignment
• Helps reduce rocking, vibration, and floor contact noise when damaged or worn
• Maintains correct clearance at the appliance bottom for proper airflow and fit

• Disconnect power and water before starting any repair.
• Use two people or proper lifting tools to tilt or lift the appliance safely.
• Basic hand tools required; follow the appliance service manual for panel removal and reinstallation.

Seal for air conditioners prevents air leaks and maintains cooling efficiency. Replace if worn, cracked, or causing energy loss. Verify fit with model number.

This is the rear grille panel for a room air conditioner that covers and protects the condenser coils and internal components at the back of the unit. It allows proper airflow for heat exchange while keeping debris and objects out. Replace this grille if it is cracked, broken, or warped, which can restrict airflow, reduce cooling efficiency, or leave internal parts exposed.

This is a plastic rear grille that mounts on the back of a room air conditioner unit. It covers and protects the condenser coils and internal components while allowing proper airflow for heat exchange. Replace this grille if it is cracked, broken, or has missing louver sections that could allow debris to enter the unit or reduce cooling efficiency.

Seal and spacer kit for air conditioners. Replace when you notice air leaks, reduced cooling efficiency, or during unit maintenance. Verify fit with your model number before ordering.

Assorted screws and clips for securing air conditioner panels and components. Replace missing, stripped, or damaged mounting hardware to restore fit.

Fix an air conditioner that won't cool or makes loud noises with this compressor. Advanced repair requiring refrigerant handling and electrical work.

Filter drier removes moisture and contaminants from your air conditioner's refrigerant system. Replace when cooling performance drops or after repairs. Verify fit with your model number.

Fix an air conditioner that won't respond to controls or displays error codes with this electronic control board. Moderately challenging repair restores function.

Replacement wire for air conditioner electrical connections. Needed when original wire is damaged, frayed, corroded, or broken during repairs or maintenance.

This capacitor provides the electrical boost needed to start and run the fan motor in a room air conditioner. It stores and releases energy to keep the motor operating at the correct speed. Replace this capacitor if the fan motor hums but does not start, runs sluggishly, or if the unit shuts off intermittently.

If your air conditioner won't start or runs but doesn't cool properly, the capacitor may have failed. This part stores electrical energy to start the compressor.

Fix unresponsive controls or error codes with this electronic control board. Restores button functions and temperature management in room air conditioners.

This is a thermistor-style temperature sensor that monitors the evaporator coil temperature in a room air conditioner. It sends temperature readings to the control board so the unit can regulate cooling cycles and prevent the evaporator from freezing over. Replace this sensor if the air conditioner runs continuously without cycling off, fails to cool properly, displays an error code, or if the evaporator coil ices up excessively.

The Thermistor is an OEM replacement part for Frigidaire room air conditioners. Located within the air conditioner unit, the thermistor accurately monitors and regulates the equipment's internal air temperature. Precisely calibrated at the factory, the thermistor allows the unit to continuously achieve and maintain the preset cooling level preferred by the user. 

Symptoms of a bad thermistor include:  

• Inconsistent or fluctuating room temperatures
• Difficulty reaching or maintaining desired temperatures  
• The control panel shows abnormal temperature readings

Causes can be age-related deterioration of sensing components, moisture exposure damaging circuitry, or loose wiring connections preventing exact temperature measurement over time. This OEM thermistor restores precise temperature control.

Replacing a faulty thermistor prevents improper compressor cycling which wastes energy. Compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Lost your air conditioner remote? This handheld remote restores wireless control of temperature, fan speed, and modes from across the room.

Replacement power cord for room air conditioners. Connects unit to electrical outlet. Replace if cord is damaged, frayed, cracked, or missing.

This wiring diagram is the factory electrical schematic used to identify wiring paths and component connections, helping you read and trace circuits for accurate diagnosis and repair. What it does:

• Shows wiring routes, connector labels and circuit paths for the appliance's electrical system
• Helps locate which wires feed specific components and where connectors plug in
• Useful when troubleshooting power loss, intermittent operation or component failures
• Clarifies control board and harness relationships for testing and repair

• One wiring diagram sheet

• Always disconnect power before accessing wiring or panels
• Use the diagram as a reference for diagnosis; confirm wiring and colors on the actual unit
• Do not cut or splice the factory wiring diagram itself; replace panels and retain the diagram for reference