Parts for Ge CT9550SH2SS: Upper Door Parts

Replacement badge designed to restore the appliance's exterior appearance and factory look. This decorative emblem replaces a faded, scratched, or missing badge so the control panel or door presents a clean, branded finish. What it does:

• Replaces a worn, cracked, faded, or missing badge to restore original appearance
• Sits on the appliance front where the original emblem was located for accurate visual match
• Helps maintain a factory-fresh look after cosmetic damage or panel repair
• Sold as the individual decorative emblem; intended as a direct-fit cosmetic replacement

• Clean and fully dry the mounting area before installing to ensure proper adhesion and fit
• Align carefully with the original location; press firmly and evenly to secure the badge

This door liner kit replaces a damaged or worn refrigerator door interior to restore a clean, sealed surface and improve door appearance. Designed to fit the OEM mounting points for a proper fit and reliable performance. What it does:

• Replaces cracked, warped, stained or otherwise damaged door liner surfaces
• Restores a smooth interior surface to help door shelves and bins mount correctly
• Helps maintain a consistent door seal by providing a true mounting surface for gaskets and hardware
• Improves overall appearance of the refrigerator door interior

• Disconnect power to the appliance before beginning service
• Remove door shelves, bins, and any trim before removing the old liner
• Retain and reuse any existing screws, clips, or hardware unless replacements are provided in the kit

This door insulation retainer is a small plastic clip that secures insulation inside a refrigerator/freezer door to help maintain proper temperature and reduce noise. It replaces worn or missing retainers to keep the door liner insulation in place. What it does:

• Secures the door insulation to the inner door liner so insulation stays positioned
• Helps prevent insulation from shifting or sagging that can affect door seal performance
• Commonly used when insulation falls out or the liner shows gaps around the insulation
• Works as a direct-fit replacement for the original retainer designed for the door assembly

• One door insulation retainer clip

• Installation generally requires removing the door panel or liner; keep track of fasteners and trim
• Handle the door liner and insulation carefully to avoid damage or tearing the insulation
• Use proper tools and disconnect power if working near electrical components or lights
• Replace all affected clips for an even, secure fit

A replacement liner support that secures the refrigerator cabinet liner and keeps interior trim and panels aligned for a proper seal and appearance. Restores stability to cracked or broken support points. What it does:

• Holds the cabinet liner and interior trim in position to prevent gaps and movement
• Helps maintain door seal alignment by keeping liner edges stable
• Reduces rattling or shifting caused by a damaged support
• Commonly replaced when liner pieces are cracked, broken, or loose

• One liner support

• Disconnect power to the appliance before beginning any repair
• Remove food, shelves, and trim pieces as needed to access the damaged support
• This part typically secures with clips or fasteners; inspect existing hardware and replace if necessary

The Oven door gasket is an OEM part for GE wall ovens and ranges. It fits around the inner rim of the oven door, creating an essential heat and air seal when closed. 

Symptoms of a bad door gasket include: 

• Excessive heat loss around the door when preheating or cooking  
• Ghosting or condensation buildup visible on the door glass
• Worn or misshapen gasket that no longer presses firmly against the door rim

Gasket material naturally hardens over time through repeated exposure to temperature changes. Accidental damage from cleaning can also impact the gasket's integrity. Replacing it with this genuine GE part helps maintain an efficient cooking environment. 

This OEM GE replacement gasket is also compatible with some Kenmore, Hotpoint, and RCA wall oven and range models. Proper sealing is important for energy efficiency as well as consistent cooking results.
 

A replacement door handle and end cap assembly that restores secure grip and a finished appearance to your appliance door. Replaces a broken, loose, or cracked handle endcap so the door is easier and safer to open. What it does

• Replaces damaged or worn handle and end cap to restore proper door grip and alignment
• Prevents sharp edges or loose parts that can catch or cause injury when opening the door
• Stops rattling or wobble caused by a cracked end cap or failing attachment points
• Matches the original fit and mounting points for straightforward replacement

• One handle and end cap assembly

• Basic hand tools typically required;
• Remove power or unplug appliance if removing a door where wiring is present; otherwise follow lockout/tagout best practices
• Handle parts can be sharp—wear gloves and protect finishes during installation
• Keep all fasteners and small parts;

This is an outer door assembly manufactured by General Electric to replace a broken or faulty door in wall ovens.The outer door assembly attaches to the door panel to protect the appliance and also provide the right aesthetic look. Over time, the outer door can easily become worn, dented, bent, scratched, detached, or otherwise broken, thus requiring replacement. Care should be taken when attempting to replace the outer door assembly as it may be too heavy for a single user. To prevent injury, always wear work gloves and disconnect the appliance from power sources. This genuine OEM outer door assembly is sold individually and manufactured from high-quality and durable materials. It is compatible with various wall ovens manufactured by General Electric, Hotpoint, and RCA.

A door handle spacer that fits behind a range of GE appliance handles to ensure correct fit and alignment, restoring a snug, finished appearance. Helps keep the handle positioned and prevents contact rubbing. What it does:

• Positions the door handle at the correct distance from the door surface for proper fit and operation
• Helps prevent handle wobble, rubbing, and cosmetic gaps
• Supports secure attachment of the handle to the door assembly
• Useful when replacing a damaged or missing spacer during handle repair

• One door handle spacer

• Install with the handle hardware in the correct order; confirm orientation before tightening
• Use proper-size screwdrivers; avoid over-tightening fasteners to prevent cracking the spacer
• Disconnect power or follow appliance-specific safety instructions when working near electrical components or heating elements
• Replace those components as well for a reliable repair

This right-hand replacement door hinge secures and pivots the appliance door, restoring proper alignment and smooth opening/closing. It helps fix a sagging, misaligned or noisy door so the seal closes correctly. What it does

• Replaces the right-hand hinge that supports and guides the door pivot.
• Helps correct a door that sags, drags, or does not seal tightly.
• Stops rubbing, binding, or grinding noise caused by a worn hinge.
• Restores proper door alignment for better cooling performance and gasket contact.

• One right-hand door hinge

• Unplug the appliance or disconnect power before beginning work.
• Support the door while removing/installing the hinge to prevent dropping or damage.
• Reuse existing mounting hardware only if undamaged; replace stripped or bent fasteners.
• After installation, check door alignment and gasket seal; adjust hinge position as needed.

This left-side refrigerator door hinge replaces a worn or damaged hinge to restore proper door alignment and smooth opening. It secures the door to the cabinet and helps maintain a tight seal for efficient cooling. What it does:

• Provides the pivot point for the left refrigerator door so it opens and closes smoothly
• Helps keep the door aligned to prevent rubbing, gaps, or scraping
• Supports the door weight to reduce sagging and strain on the seal
• Can resolve symptoms like uneven door gap, noisy movement, or doors that won't stay closed

• Unplug the appliance or shut off power before beginning any work
• Support the door while removing and installing the hinge to prevent drops or injury
• Retain and reuse any original screws or fasteners unless replacements are provided

ST10-16 X 7/16"

Black. 8-18 AB HXW 3/8