Parts for Ge PGS960YP1FS: Upper Door Parts

Includes 12 washers.

The GE Glass and Panel Door Assembly is an OEM component specifically designed for GE wall oven models. It consists of tempered glass surrounded by an outer steel panel door. 

Causes of a bad door assembly can include normal wear and tears developing hairline fractures in the glass over time from repeated heating and cooling cycles. Accidental drops or impacts during cleaning could crack or compromise the integrity of the materials.

Symptoms of failure include:  

• Fogging or condensation between the panes of glass
• The door becoming misaligned and no longer closing properly  
• Gaps developing at the seams between glass and frame
• Cracks or chips appearing on visible surfaces

This authentic GE replacement is compatible with additional brands including Hotpoint, RCA and select Kenmore models.

This Cover Vent Trim is the outer trim piece that finishes and protects the appliance vent opening, restoring a clean appearance and helping keep the vent area sealed against debris and dust. What it does:

• Replaces damaged, bent, or missing vent trim to improve the look and fit of the vent opening
• Helps keep lint, dust and large debris from collecting at the vent edge
• Restores proper alignment of the vent opening trim for a secure fit
• Useful when the existing trim is dented, cracked or cosmetically worn

• One cover vent trim piece as shown

• Designed for a direct replacement; check that part number matches the old trim before installation
• Requires only basic hand tools; remove fasteners or clips holding the old trim and secure the new piece in place
• Disconnect power to the appliance before working in the vent area
• If vent damage extends beyond the trim, inspect the vent and surrounding components and replace additional parts as needed

This stainless steel oven door handle gives your range a finished look and a safe, sturdy grip for opening and closing the oven. It replaces a damaged, loose, or missing handle to restore normal operation and appearance. What it does

• Provides a secure handhold for opening and closing the oven door.
• Replaces handles that are bent, dented, cracked, or have stripped mounting holes.
• Stops wobble or play from loose or damaged handles when tightened or replaced.
• Restores the appliance's appearance with a stainless steel finish.

• One stainless steel oven door handle

• Disconnect power to the appliance before beginning work; allow the oven to cool completely.
• Support the oven door when removing or installing the handle to prevent dropping or pinching.
• Use the correct fasteners and hand tools; tighten mounting screws securely but avoid over-torquing.

This handle mounting bracket secures the appliance handle to the door, restoring a stable grip and normal operation. Replace a cracked or worn bracket to stop a loose, wobbly or detached handle and make the door easier to open. What it does:

• Provides the structural support that fastens the exterior handle to the appliance door
• Stops handle wobble or play caused by a broken or worn bracket
• Restores proper handle alignment and secure attachment
• Helps prevent further damage to the handle or door trim by replacing a failing mount

• Unplug the appliance or disconnect power before beginning any repair
• Remove the handle and any trim to access the bracket; keep mounting screws for re-use unless replacement screws are specified
• Install bracket with correct orientation and torque; avoid overtightening to prevent cracking

This bracket handle is the replacement mounting bracket that secures a refrigerator/freezer door handle, restoring proper handle alignment and support. It helps stabilize the handle and prevent movement or looseness for reliable daily use. What it does

• Secures the door handle to the appliance cabinet so the handle stays firmly in place
• Restores correct handle alignment and feel after a broken or worn bracket
• Reduces handle wobble, prevent further damage to the handle or door
• Matches OEM fit and form for direct replacement where this bracket is specified

• Basic hand tools required; remove power and empty door pockets before starting
• Follow OEM disassembly steps to avoid damaging trim or the door finish
• Keep hardware and screws from the original assembly; replace only with manufacturer-specified fasteners

This oven door inner insulation cushions the inner door panel and helps maintain proper cooking temperatures while reducing heat transfer to the outer door. Replaces damaged or missing insulation to improve heating consistency and help keep the exterior cooler. What it does

• Fills the cavity behind the oven door's inner panel to limit heat loss and stabilize internal temperatures.
• Helps reduce outer door surface temperature for safer handling during and after use.
• Reduces drafts and uneven cooking caused by compromised or missing insulation.
• Works with the door inner panel and outer door assembly to restore proper sealing and performance.

• One door insulation

• Remove power to the appliance and allow the oven to fully cool before beginning work.
• Handle carefully to avoid tearing the insulation; use caution around sharp sheet metal and door glass.
• Follow manufacturer service manual or OEM instructions for door disassembly and reassembly.

Size: 10-32 GXTT FLP.595 S