Parts for Ge CGS990SET4SS: Upper Oven Parts

This replacement screw secures appliance components so panels, brackets, and trim stay tight and aligned. Use it to replace a missing, stripped, or rusted fastener and restore a solid, rattle-free fit in the affected assembly.

• Fastens parts to the chassis/frame or mounting brackets
• Replaces lost, damaged, or corroded hardware
• Can help address loose or vibrating panels and minor misalignment
• Maintains a secure attachment during normal operation

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Match the screw to the original location and reuse any clips or washers if present
• Start threading by hand to avoid cross-threading; tighten snugly without overtightening
• Repair/replace damaged receiving threads or clip for proper hold

This plunger switch is the push-style electrical switch that completes a circuit when an actuator is depressed, restoring reliable on/off signaling. Use it to replace a worn or broken plunger switch that causes intermittent or non-responsive operation. What it does:

• Closes an electrical circuit when the plunger is pushed, sending a signal to the appliance control.
• Commonly used where a door, lever or dispenser actuator must register a position or user input.
• Can correct symptoms like intermittent operation, a dispenser or mechanism that won't activate, or a stuck/unresponsive actuator.
• Acts as a direct mechanical-to-electrical interface—no electronics required.

• Disconnect power (unplug or turn off breaker) before servicing to avoid shock.
• Remove the access panel or housing to reach the switch; note actuator orientation before removal.
• Disconnect terminals or harness, then swap the old switch for the new one; reconnect terminals securely.
• Test the plunger action and appliance function before reinstalling panels.

The Oven Lamp Holder is an OEM part for GE ovens. This component securely holds the oven light bulb in place, ensuring proper illumination inside the oven cavity for better visibility during cooking and baking.

Causes of a bad lamp holder can include repeated exposure to high temperatures, physical damage, or electrical issues. A malfunctioning lamp holder can lead to the oven light not functioning correctly or at all.

Symptoms of a bad oven lamp holder include:

• The oven light not turning on
• Flickering or intermittent operation of the light
• Visible damage or corrosion to the lamp holder
• The light bulb not staying securely in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This angle support is a small metal mounting bracket that stabilizes and secures components inside the appliance, helping keep shelves, panels, or assemblies aligned for reliable operation and safe use. What it does:

• Provides structural support for interior panels, shelves, or trim to prevent sagging or misalignment
• Holds assemblies in the correct position to reduce rattling and vibration during use
• Restores proper fit and clearance when a bent or broken bracket causes shifting
• Works with fasteners to anchor components where a right-angle connection is needed

• Inspect surrounding parts and fasteners; replace any damaged screws or clips as needed
• Use the correct size fastener and torque to avoid stripping or cracking adjacent parts
• Disconnect power and follow manufacturer safety guidelines before working near electrical components

This oven light gasket fits between the glass lens and the oven liner. It restores a proper seal around the light opening to help keep grease and moisture out of the light cavity and hold the lens securely in place. What it does:

• Seals the joint between the oven light lens and the cavity wall
• Helps prevent grease and moisture from entering the light assembly
• Keeps the lens snug to reduce looseness or rattling
• Replace if the gasket is cracked, flattened, brittle, missing, or if moisture/grease is visible around the lens

• One oven light lens gasket

• Disconnect power at the breaker and allow the oven to cool completely
• Remove the light lens/retainer as your model requires (unscrew lens or release clips)
• Note gasket orientation and clean the mating surfaces
• Seat the new gasket evenly and reinstall the lens; do not overtighten the glass

This automatic door latch secures the dryer door during operation so the appliance can run safely and reliably. Designed to replace a worn or broken latch and restore proper door closure. What it does:

• Secures the dryer door so the machine can start and operate
• Prevents the door from popping open mid-cycle
• Helps stop dryer from failing to start due to a faulty latch switch
• Common symptom: dryer won't run or stops when the door is closed

• One automatic door latch

• Disconnect power (unplug or shut off breaker) before beginning any repair
• Access typically requires removing the dryer front or door assembly; keep fasteners organized
• Verify striker plate alignment and door fit when installing the new latch

This capillary clip secures the oven thermostat's sensing bulb/capillary to the cavity wall so it stays correctly positioned for accurate temperature control. Replace a missing or damaged clip to prevent a sagging bulb and erratic oven performance.

• Holds the thermostat capillary tube/sensing bulb in place inside the oven
• Helps maintain consistent temperature regulation by keeping the bulb properly located
• Direct replacement for a broken, corroded, or missing clip
• Symptoms include a loose or dangling bulb, uneven baking, or temperature swings

• Disconnect power (and gas, if applicable) and allow the oven to cool completely
• Access the oven cavity; locate the thermostat sensing bulb and capillary along the wall or back panel
• Position the bulb/capillary and secure with the new clip; avoid kinking or crushing the tube
• Restore power, and test operation

This slice rack assembly is the removable wire rack that holds food slices or pans inside the oven/toaster cavity, restoring proper support and spacing for even heating and safe handling. What it does

• Replaces a bent, warped, or missing slice rack so cookware and food sit level during cooking
• Restores proper airflow and spacing for more consistent toasting/baking performance
• Eliminates rattling or instability caused by damaged rack supports
• Makes it easy to slide items in and out without snagging

• One slice rack assembly (exact configuration as shown on parts diagram)

• Remove power and allow the appliance to cool before replacing the rack
• Slide the replacement rack into the existing guides; ensure it seats evenly on both sides
• No special tools required for most installs; inspect guides for damage before use
• If rack does not seat properly, check oven rails or support brackets for wear

This oven bottom inner liner replaces the flat interior panel that forms the floor of the oven cavity, protecting the heating elements and supporting cookware for stable, even baking. What it does:

• Forms the flat bottom surface of the oven cavity and protects internal components from spills and drips
• Supports cookware and helps maintain proper airflow for consistent cooking results
• Replaces warped, cracked, dented, or corroded bottoms that can trap food debris or cause uneven heating
• Restores a clean interior surface and prevents spills from reaching insulation or electrical parts

• Disconnect power to the appliance before starting any repair
• Remove oven racks and any access panels needed to reach mounting screws; some models may require lifting or removing the cooktop
• Handle edges carefully — sheet metal can be sharp; use gloves and eye protection
• Use OEM fasteners and follow model-specific instructions for correct fit and safe reassembly