Parts for Bosch HDI7282U/08: Valves Parts

This jet holder is the mounting support that secures a dishwasher spray arm nozzle assembly, helping maintain proper spray alignment for consistent cleaning performance. It replaces a worn or broken holder that lets the arm wobble or spin incorrectly. What it does:

• Anchors the spray arm or nozzle assembly so the spray arm rotates smoothly and stays aligned
• Restores proper water spray pattern when a damaged holder allows the arm to wobble or detach
• Helps stop leak paths or reduced cleaning due to misdirected spray
• Works with existing spray arm and fasteners to return normal operation

• One jet holder

• Disconnect power and water to the appliance before starting any repair
• Access typically requires removing the lower or upper spray arm and any kickplate or tub components; retain all fasteners
• Inspect the spray arm and mounting hardware for related wear and replace if damaged

The Electrode is an OEM component specifically designed for select Bosch gas range models featuring a pilot ignition system. Located near the gas valve, it initiates sparking to reliably light burners on demand. Consistent placement ensures safe and dependable burner ignition.

Symptoms of a faulty electrode commonly involve failure to produce sparks stopping burners from lighting properly. Regular flareups increase electrode wear warranting timely replacement.

Causes of a bad electrode include normal arc erosion reducing spark output. Deposits inhibiting consistent contact necessitate cleaning or a component change.

Causes of a bad electrode can involve:

• Burners lighting sporadically or requiring multiple ignitions
• Pilot lights repeatedly going out between uses   
• Inability to ignite burners for cooking

This OEM Bosch part is also compatible with some Dacor, Thermador, and Blomberg gas ranges. 
 

This water inlet valve controls dishwasher water flow during fill cycles, restoring proper filling and preventing overfill. Replace a faulty valve to stop no-fill, slow-fill, or continuous-fill issues and restore normal wash cycles. What it does:

• Opens and closes to admit water into the dishwasher during fill cycles
• Maintains correct water flow and pressure for proper wash performance
• Stops water flow if inlet fails closed or prevents filling if stuck open
• Common symptom link: dishwasher won't fill, fills slowly, or shows error/overflow conditions

• One water inlet valve

• Disconnect power and shut off the water supply before starting
• Turn off the breaker; water and electrical safety first
• Basic hand tools typically required; keep track of hose clamps and fittings
• Inspect inlet hoses and gaskets and tighten or replace clamps as needed

This clamp secures flexible hoses and small tubes to fittings, keeping connections tight to help prevent leaks and movement. It's a small replacement clip used on water and drain lines in many appliances. What it does

• Holds a hose or tube firmly to a barb or nipple to maintain a sealed connection
• Helps stop leaks caused by loose or damaged hose connections
• Prevents hoses from slipping off during operation and reduces vibration noise
• Used wherever a small retaining clamp is required on water or drain lines

• One clamp

• Turn off power and shut off water supply before replacing the clamp
• Slide clamp over the hose, push hose fully onto the fitting, then compress or tighten clamp as required
• Use pliers or the correct tool for the clamp type; avoid damaging the hose when installing
• Replace if corroded, cracked, or not seating properly

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where the original screw is missing, stripped, or damaged to help keep parts aligned and stable. What it does:

• Fastens panels, brackets, or components to maintain proper alignment and operation
• Replaces a lost, stripped, or damaged screw to prevent rattling or loose parts
• Provides the same basic fastening function as the original hardware
• Suitable where the appliance requires a small machine/tapping screw of the correct size and thread

• One replacement screw

• Use the correct screwdriver or bit to avoid stripping the head
• Start threading by hand to ensure proper engagement before tightening
• Tighten snugly but avoid over-torquing which can strip threads or damage parts
• Disconnect power to the appliance before working on or removing panels where appropriate;