Parts for Thermador UCV245DS-01: Vent System Parts

Fixes downdraft range hood lights or fan not working. This transformer converts voltage for proper lighting and ventilation operation. Moderate DIY repair.

Flexible sealing strip creates a tight closure along your downdraft vent door edge to prevent air leaks and maintain efficiency. Replace when worn or damaged.

Mounting bracket for downdraft ventilation systems. Secures the unit to cabinetry or countertop. Replace if bent, cracked, or missing hardware slots.

Replacement mounting bracket for downdraft ventilation systems. Secures panels and components for proper alignment. Replaces damaged, cracked, or missing brackets.

This cover is a molded trim piece that restores the appliance's finished appearance and protects underlying components from dirt and damage. It replaces broken or missing covers to improve safety and maintain proper operation. What it does:

• Conceals and protects internal components behind the appliance cabinet or control area
• Prevents debris buildup and accidental contact with exposed parts
• Restores the original cosmetic appearance where the cover was damaged or missing
• Common symptom: cracked, broken or missing cover leaving components exposed

• One replacement cover as shown

• Disconnect power (unplug or switch off breaker) before beginning any work
• Installation typically requires removing adjacent trim or a few screws; keep hardware for reassembly
• Handle carefully to avoid scratching the finish and ensure clips/tabs fully engage

Sleeve component for downdraft ventilation systems and range hoods. Replaces damaged, cracked, or missing sleeves during installation or repair work.

Flat metal washer for downdraft ventilation systems and range hoods. Replaces lost, corroded, or damaged washers during assembly or repair work.

Internal protective sheet for downdraft ventilation systems. Replaces torn, missing, or damaged panels that shield wiring and components inside your unit.

Stress relief component for downdraft ventilation systems and range hoods. Replaces worn, damaged, or missing parts during installation or repair.

Metal grease filter for downdraft ventilation systems. Replace when grease buildup reduces airflow or cleaning no longer restores performance. Verify fit with your model number before ordering.

Spring guide that attaches to the cushion spring bracket in downdraft ventilation systems. Replace if cracked, broken, or missing to secure the spring.

Range hood not turning on or fan speeds not working? This switch controls power and speed settings. Common repair for unresponsive controls.

This cable harness routes power and signals between components to restore electrical connectivity in the appliance. It replaces a damaged or worn wiring assembly to help the appliance power and control circuits operate correctly. What it does:

• Transfers power and control signals between modules, switches, and motors
• Replaces frayed, burned, or broken wiring that causes intermittent power or control failures
• Helps stop faults like non-starting units, control panel errors, or circuits that won't energize
• Matches OEM connector ends and wire grouping to maintain original electrical routing and function

• For safety, disconnect power at the breaker or unplug the appliance before servicing
• Inspect connectors and routing before and after install to avoid pinching or chafing wires
• Use only the exact harness variant specified for your model; secure with original clips/fasteners

Fix ventilation control issues with this downdraft cable harness. Restores power to blower motors and controls. Direct replacement for most systems.

Fix a range hood that won't turn on or respond to controls with this switch replacement. Common for fan or light control failures. Basic repair.

This part is a Bosch oven range and vent hood control module. The purpose of this component is the direct control of the stove's range top cooking area and the hood vent/fan area. When the range top only powers individual burners or doesn't heat to temperature properly, this could indicate the need for a new control board. This model controls the hood range as well, meaning the light and fan would stop working also. On the oven this part is made for, the range control board would be housed directly on the top-front portion of the stove. The range slides out, allowing access to the back of the range control. Disconnect the control board from the range assembly. Reconnect the new component and fasten it back into place.This is a genuine OEM product and is sourced directly from the manufacturer as an individual component. Only Bosch ranges are compatible with this product.