Parts for Whirlpool WET4024EW0: 02 - Washer / Dryer Control Panel Parts

Wire harness for washer dryer combo units. Replaces damaged, frayed, or corroded wiring assemblies. Essential when connectors are broken or worn.

Round control knob for laundry center control panels. Replaces cracked, faded, or loose knobs on temperature and function selectors. Fits splined shafts.

Replacement control dial for laundry center selector knobs. Restores worn, cracked, or missing dials so you can choose cycles and settings with a secure grip.

If your washer won't advance through cycles, won't drain, or won't spin, the timer may be faulty. Moderately difficult repair requires console removal.

This endcap is a direct-fit replacement housing end cap that helps protect and support adjacent components, keeping internal parts aligned and reducing wear. It restores proper fit and function where a damaged or missing endcap causes noise or misalignment. What it does

• Covers and protects the end of the housing to prevent debris entry and reduce component wear
• Helps maintain correct alignment of internal parts to minimize vibration and noise
• Replaces cracked, broken, or worn endcaps that can allow movement or rubbing
• Useful when visible damage or play is present at the housing edge

• Disconnect power (and water if applicable) before beginning any repair
• Basic disassembly of the appliance's housing or access panel is usually required; keep fasteners organized
• Inspect surrounding seals, gaskets, and mounting tabs for damage and replace if needed

Replacement mounting screw that secures panels and components in place. Install this fastener when the original is missing, stripped, or damaged.

The Clip is an OEM part for Whirlpool dryers. This part secures the control knob to the dryer’s control panel, ensuring it remains firmly attached and functions correctly. The clip helps provide stability and precise control over the dryer settings.

Causes of a bad clip can include regular wear and tear, accidental damage during use, or stress from frequent adjustments.

Symptoms of a bad clip include:

• Knob becoming loose or falling off
• Difficulty turning the knob to adjust settings
• Knob not staying securely in place
• Knob wobbling or feeling unstable

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This temperature switch is the user-control that selects and regulates heat settings, restoring proper temperature selection and cycle performance. It provides a direct replacement for a worn or faulty selector switch. What it does:

• Routes power to the heating system according to the chosen temperature setting
• Helps maintain correct operating temperature for the selected cycle
• Commonly replaced when the appliance fails to heat properly or temperature settings don't change
• Acts as the user interface control for temperature selection on the control panel

• One temperature switch

• Disconnect power (unplug or turn off breaker) before beginning any repair
• Access typically requires removing the control console or panel; keep track of screws and connectors
• Handle wiring harnesses and terminals gently; match wire locations during reassembly

Control knob for laundry center. Installs on the control panel to operate cycle selection and settings. Replace if cracked, broken, or missing.

Fix a loose or non-functioning console lock with this replacement spring. Restores proper tension to the control lock mechanism. Simple repair for DIYers.

Fix a loose or rattling control panel with this console lock screw. Secures the console assembly to the cabinet for stable, aligned controls. Quick fix.

This 4-cycle dryer timer controls the sequence and duration of your drying programs. Replace it to restore proper cycle advance and automatic shut-off when the unit stalls mid-cycle or runs past the set time.

• Sequences power to the motor and heater based on the selected program
• Advances the cycle and turns the dryer off at the end of the set time
• Supports timed drying and cool-down functions
• Common symptoms of a failing timer: cycle won't advance, runs too long/short, or won't shut off at end

• Disconnect power; for gas models, shut off gas supply
• Access the control console; remove the knob and rear panel as needed
• Transfer wires one at a time to matching terminals;
• Secure the timer, reassemble the console, and test all cycles

Control panel won't stay closed or pops open during cycles? This console lock secures the control console and prevents accidental setting changes.

Fix a dryer that won't start or responds intermittently when you press the button. This push-to-start switch is a straightforward replacement.

Control knob for washer dryer combo units. Replaces broken, cracked, or missing knobs on the control panel. Direct replacement part for dial operation.

Missing cycle-end beeps or touchpad sounds? This buzzer assembly restores audible alerts for completed cycles and error notifications. Direct fit replacement.

Secures the control console to the cabinet, preventing rattles and loose movement. Replace when the panel sags or won't stay in place. Confirm fit.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Replace your laundry center's control dial when cracked, stripped, or missing. Installs on the control panel shaft to restore setting selection.