Parts for Whirlpool WET4027HW2: Washer / Dryer Control Panel Parts

Replace a damaged or worn control console with this complete console assembly to restore the appliance's control area and button/knob mounting. It provides the mounting surface and openings for the user interface so controls sit securely and operate correctly. What it does:

• Houses and secures the user controls, display window, and selector openings
• Restores proper alignment and fit of buttons, knobs, and trim for normal operation
• Protects internal control components from dirt and impact
• Helps eliminate issues caused by cracked, bent, or loose console panels

• Disconnect power (unplug or switch off breaker) before beginning any work
• Support the cabinet or console during removal to avoid dropping or damaging adjacent parts
• Some transfers of switches, bezels, or trim may be required; keep fasteners and parts organized
• Use common hand tools

Note: 5  Position Switch
 

Note: 2-Position Switch

The Push to Start Switch is an OEM replacement part for Whirlpool dryers. Located on the control panel, it allows the user to initiate the drying cycle with the push of a button. This switch is designed to withstand the repetitive motions of starting countless loads over the dryer's lifespan.

Causes can be gradual wear of internal components like contact pads from activations, or moisture intrusion corroding circuit pathways over time.

Symptoms of a faulty push-to-start switch include:

• The dryer failing to start even when powered on
• Inconsistent or intermittent operation of the start button
• The dryer starting unintentionally without input

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Knob Kit is an OEM replacement part for Whirlpool washing machines and dryers. Including a set of premium knobs color-matched to the appliance controls, this kit restores complete interfaces whenever old or damaged buttons need replacing. The kit includes 1 timer knob and 3 control knobs.

Causes for replacement involve normal wear from repeated touching during cycles as well as impact damage from falls or button presses gone awry over many years of service.

Symptoms necessitating a new knob kit include:

• Cracked, broken or missing buttons impeding normal operations
• Loosened knobs slipping out of holes or wearing partial turns
• Discolored faded markings obscuring switch positions

This OEM Whirlpool part is also compatible with Maytag, Amana, and other major brands.

The Knob Kit is an OEM replacement part for Whirlpool washing machines and dryers. Including a set of premium knobs color-matched to the appliance controls, this kit restores complete interfaces whenever old or damaged buttons need replacing. The kit includes 1 timer knob and 3 control knobs.

Causes for replacement involve normal wear from repeated touching during cycles as well as impact damage from falls or button presses gone awry over many years of service.

Symptoms necessitating a new knob kit include:

• Cracked, broken or missing buttons impeding normal operations
• Loosened knobs slipping out of holes or wearing partial turns
• Discolored faded markings obscuring switch positions

This OEM Whirlpool part is also compatible with Maytag, Amana, and other major brands.

This Timer is the mechanical cycle controller for your appliance. It sequences power to components so cycles start, advance, and end at the proper times, helping restore dependable operation when the original timer wears or fails.

• Sequences power to motors, valves, and heaters according to the cycle selected at the timer shaft
• Advances the machine through each stage via a motor-driven cam and internal contacts
• Symptoms: cycle doesn't advance or stops mid-cycle
• Symptoms: appliance won't start or only starts intermittently
• Symptoms: runs past the end of the cycle or won't shut off

• Disconnect power before servicing; shut off water supply
• Photograph wiring and transfer wires to the same labeled terminals one at a time
• Reuse the original mounting hardware, dial, and knob
• After installation, run a short test cycle to ensure the timer advances properly

This hinge bracket secures a refrigerator door hinge to the cabinet, restoring proper door alignment and support so the door seals and closes reliably. Designed to replace a worn, bent, or broken hinge mounting bracket. What it does:

• Provides a stable mounting point for the door hinge assembly to prevent sagging or drooping
• Restores correct door alignment to improve sealing and reduce cold air loss
• Stops excess movement or rattling at the hinge area
• Helps eliminate door-binding or uneven gaps that keep the door from closing fully

• Unplug the appliance and remove food/items from the door before starting
• Support the door while removing/installing the bracket to avoid damage or injury
• Reuse or replace fasteners as required; tighten securely but avoid over-torquing
• After installation, check door alignment and gasket seal; make minor adjustments as needed

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.