Parts for HLP23E: Washer Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This water valve absorption gasket is a replacement seal that fits between the water valve and surrounding housing to maintain a watertight connection and prevent leaks. It restores a secure seal for proper valve operation and leak control. What it does:

• Creates a watertight seal at the water valve mounting interface to stop drips and seepage.
• Helps maintain correct valve alignment and prevents moisture from reaching nearby components.
• Addresses symptoms such as visible leaking at the valve, water on the cabinet floor, or moisture buildup near the valve area.
• Supports reliable water flow by preventing external leaks that can affect valve performance.

• One water valve absorption gasket

• Disconnect power and shut off water supply before servicing; relieve pressure in lines.
• Inspect mating surfaces and clean away debris or old gasket material before installing the new gasket.
• Replace only with the exact gasket specified for the valve to ensure a proper fit; hand-fit then tighten mounting fasteners to OEM guidance.

This out-of-balance micro switch is the load-sensing switch that tells the washer when a tub is unbalanced so the control can pause or redistribute the load, helping prevent excessive vibration and damage during spin cycles. What it does:

• Detects excessive tub movement or imbalance and signals the washer control to stop or adjust the spin cycle
• Helps prevent noisy, vibrating, or shifting loads from continuing to spin
• Can cause the washer to stop mid-cycle or fail to enter high-speed spin when faulty
• Works as the electrical contact that completes or interrupts the control circuit based on tub position

• Disconnect power (and water if required) before beginning service
• Access usually requires removing the top or console and inner control/sensor cover—follow your model's service instructions
• Replace the switch with the identical part and reconnect wiring harnesses to matching terminals
• Test the washer through a diagnostic or a short cycle to ensure proper operation after installation

This replacement out-of-balance lever assembly restores the washer's ability to detect and respond to an uneven load, helping reduce excessive vibration and helping the machine complete normal spin and drain cycles. What it does:

• Transfers load/balance information to the washer's suspension/sensor system so the washer can rebalance during spin
• Helps reduce excessive shaking, banging or movement caused by an imbalanced load
• Prevents repeated automatic cycle interruptions or "out of balance" error conditions when functioning properly
• Contribute to noisy or failed spin cycles if worn, broken or disconnected

• One out of balance lever assembly

• Disconnect power to the washer before beginning any repairs
• Remove the appropriate access panels and note the lever orientation and linkages before removal
• Handle springs, clips and linkages carefully; keep fasteners and small parts organized for reassembly
• After installation, run a test/spin cycle and inspect for proper operation and reduced vibration; for specific alignment or calibration steps

This dryer drive motor assembly powers the drum and blower to rotate and move air through the dryer. Replacing a failed motor restores drum rotation so loads tumble and dry properly. What it does:

• Turns the dryer drum so clothes tumble during the cycle
• Drives the blower to circulate air through the drum and vent
• Stops operation when internal thermal overload trips to protect the motor
• Common symptoms: drum won't turn, motor hums but won't start, or dryer stops mid-cycle

• One dryer motor assembly as shown

• Disconnect power before starting any repair to avoid electric shock
• Access and removal typically require panel or bulkhead disassembly; follow OEM instructions
• Inspect and realign the drive belt and blower wheel when installing the motor
• Check and clear any ventilation or lint buildup before reassembly

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This replacement door gasket creates a tight seal to help maintain appliance temperature and prevent air or moisture leaks for reliable operation. It restores sealing performance to reduce energy loss and keep contents at the correct temperature. What it does:

• Seals the door to prevent cold/hot air from leaking in or out
• Helps maintain consistent internal temperature and efficiency
• Reduces frost buildup and moisture migration that can affect performance
• Quietly restores a proper fit to stop drafts or uneven door closing

• Disconnect power to the appliance before beginning any work
• Remove the old gasket and clean the mounting surface thoroughly before installing
• Fit the gasket evenly around the door; follow OEM alignment and seating steps

Washer won't start or stops mid-cycle? A faulty lid switch prevents operation when the lid isn't securely closed. Simple DIY fix in under an hour.

Washer lint filter traps debris and fibers during wash cycles. Replace if clogged, torn, or causing drainage issues. Confirm fit with your model number.

Washer drain bearing bushing supports smooth drainage operation. Replace if you notice leaks, unusual noise, or drainage issues. Verify fit with model.

Connects the water inlet hose to your washer's fill valve. Replace this coupler if it's cracked, leaking, or damaged to restore a secure water connection.

This V-type dryer belt powers the drum, transferring motor torque to rotate the drum for proper drying. Replaces worn or stretched belts to restore consistent drum rotation and improve drying performance. What it does:

• Wraps around the dryer drum and motor/idler to drive drum rotation
• Restores drum movement when original belt is broken, frayed, or slipped
• Helps eliminate noisy slipping or intermittent spinning caused by a loose belt
• Supports even tumbling so clothes dry more consistently

• Disconnect power (and shut off gas for gas dryers) before beginning any repair
• Observe belt routing around the drum, idler pulley, and motor pulley—refer to your model's diagram
• Inspect drum rollers, idler, and motor shaft for wear; replace if worn to prevent premature belt failure
• Use proper hand protection and avoid forcing parts

Replace your washer's damaged or worn hose. This essential component connects water lines and drainage systems. Order now if yours is cracked or leaking.

Replacement spring for the washer's out-of-balance switch lever. It restores proper lever tension so the switch can correctly sense unbalanced loads and manage the spin cycle, helping reduce vibration, noise, and nuisance stops. What it does:

• Maintains the return tension on the out-of-balance switch lever so the switch actuates reliably during spin
• Allows the control to pause or redistribute when a load is unbalanced, minimizing vibration and banging
• A weak, stretched, or missing spring can cause no-spin, repeated pauses, or cycles that end early with out-of-balance warnings
• Helps ensure accurate imbalance detection for consistent spin performance

• Includes 1 spring

• Unplug the washer before servicing
• Access the out-of-balance switch lever (location varies by model; often under the top or behind the front panel)
• Note the spring's routing and attachment points; install the new spring in the same orientation and avoid overstretching
• After reassembly, run a short spin test with a small load to confirm operation

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.