Parts for HLPW028BXW: Washer Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This water valve absorption gasket is a replacement seal that fits between the water valve and surrounding housing to maintain a watertight connection and prevent leaks. It restores a secure seal for proper valve operation and leak control. What it does:

• Creates a watertight seal at the water valve mounting interface to stop drips and seepage.
• Helps maintain correct valve alignment and prevents moisture from reaching nearby components.
• Addresses symptoms such as visible leaking at the valve, water on the cabinet floor, or moisture buildup near the valve area.
• Supports reliable water flow by preventing external leaks that can affect valve performance.

• One water valve absorption gasket

• Disconnect power and shut off water supply before servicing; relieve pressure in lines.
• Inspect mating surfaces and clean away debris or old gasket material before installing the new gasket.
• Replace only with the exact gasket specified for the valve to ensure a proper fit; hand-fit then tighten mounting fasteners to OEM guidance.

This rear foot is a replacement stabilizing leg that supports and levels the back of the appliance, restoring proper balance and reducing rocking or vibration for safe, even operation. What it does:

• Replaces a worn, cracked, or missing rear foot to restore stability
• Provides a firm mounting point at the appliance rear to prevent rocking
• Helps maintain correct appliance height and alignment for doors and seals
• Reduces vibration and noise caused by uneven flooring

• One rear foot

• Turn off power and disconnect the appliance before servicing
• Access the rear foot by tipping or raising the appliance per manufacturer instructions
• Thread or press the replacement foot into the mounting socket until secure; verify even leveling with the front feet

An adjustable leveling foot that stabilizes and levels ranges and other freestanding appliances for safe, even operation. Helps stop rocking and lets you fine-tune appliance height for proper door alignment and countertop fit. What it does:

• Replaces a worn or damaged leveling leg to restore a firm, level base
• Adjusts appliance height to correct uneven floors and prevent rocking
• Helps maintain proper door alignment and seal for ovens and ranges
• Protects flooring by providing a stable, load-bearing contact point

• Disconnect power and gas and follow appliance safety procedures before working underneath or tilting the unit
• Support the appliance securely or have a helper when raising it to access the foot
• Thread or slide the foot into the mounting bracket and adjust height until the appliance sits level
• Re-check stability and connections before returning the appliance to service

Bottom cover panel for washers. Protects internal components from dust and debris. Replace if cracked, damaged, or missing for complete enclosure.

This detergent dispenser drawer is the slide-out tray that holds and releases liquid or powdered detergent for proper wash cycles. It replaces cracked, sticking, or broken drawers to restore normal detergent delivery and loading. What it does:

• Holds detergent and delivers it into the washer at the correct time during the cycle
• Replaces drawers that are cracked, warped, or jammed and won't slide smoothly
• Stops leaks or pooling caused by damaged or misshapen dispenser trays
• Restores a secure fit so the dispenser closes and stays in place during use

• Disconnect power before servicing and follow all safety instructions in your manual
• Remove the old drawer by sliding out and releasing clips or tabs as needed; install the new drawer by aligning rails and snapping into place
• Handle plastic parts gently to avoid breaking mounting tabs; do not force parts into position
• Run a test cycle with a small amount of detergent to ensure proper operation after installation

This out-of-balance micro switch is the load-sensing switch that tells the washer when a tub is unbalanced so the control can pause or redistribute the load, helping prevent excessive vibration and damage during spin cycles. What it does:

• Detects excessive tub movement or imbalance and signals the washer control to stop or adjust the spin cycle
• Helps prevent noisy, vibrating, or shifting loads from continuing to spin
• Can cause the washer to stop mid-cycle or fail to enter high-speed spin when faulty
• Works as the electrical contact that completes or interrupts the control circuit based on tub position

• Disconnect power (and water if required) before beginning service
• Access usually requires removing the top or console and inner control/sensor cover—follow your model's service instructions
• Replace the switch with the identical part and reconnect wiring harnesses to matching terminals
• Test the washer through a diagnostic or a short cycle to ensure proper operation after installation

This replacement out-of-balance lever assembly restores the washer's ability to detect and respond to an uneven load, helping reduce excessive vibration and helping the machine complete normal spin and drain cycles. What it does:

• Transfers load/balance information to the washer's suspension/sensor system so the washer can rebalance during spin
• Helps reduce excessive shaking, banging or movement caused by an imbalanced load
• Prevents repeated automatic cycle interruptions or "out of balance" error conditions when functioning properly
• Contribute to noisy or failed spin cycles if worn, broken or disconnected

• One out of balance lever assembly

• Disconnect power to the washer before beginning any repairs
• Remove the appropriate access panels and note the lever orientation and linkages before removal
• Handle springs, clips and linkages carefully; keep fasteners and small parts organized for reassembly
• After installation, run a test/spin cycle and inspect for proper operation and reduced vibration; for specific alignment or calibration steps

Suspension rod and spring assembly for washers. Installs inside the cabinet to support the wash basket. Replace if damaged, broken, or worn out.

This tub outlet clamp secures the tub outlet to the washer tub, keeping the seal and outlet assembly tight to help prevent leaks and maintain proper drain alignment. Durable spring-steel construction holds components in place during operation. What it does:

• Holds the tub outlet and gasket firmly to the washer tub to maintain a watertight seal
• Helps prevent water leaks at the tub outlet connection
• Keeps the outlet assembly aligned to reduce strain on hoses and fittings
• Supports reliable draining by maintaining a secure connection

• Disconnect power and turn off the water supply before starting any repair
• Inspect the outlet and gasket for damage; replace any worn seals when replacing the clamp
• Use pliers or a clamp tool to compress/install the spring clamp; ensure ends seat fully and evenly

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Secures the power cord strain relief to your dryer chassis. Replaces lost or damaged mounting screws to restore secure cord attachment and reduce stress.

Washer drain bearing bushing supports smooth drainage operation. Replace if you notice leaks, unusual noise, or drainage issues. Verify fit with model.

Washer not draining properly or leaking during drain cycle? This tub-to-pump drain hose carries water from the tub to the pump, restoring drainage.

Inner drain hose connects your washer tub to the drain pump. Replace if cracked, leaking, or clogged to prevent water drainage issues. Verify fit with your model.

Washer won't fill properly or overfills? This water level pressure switch senses and signals correct fill levels, preventing overfill and underfill issues.

Washer won't start or stops mid-cycle? A faulty lid switch prevents operation when the lid isn't securely closed. Simple DIY fix in under an hour.

Secures the washer lid hinge to the cabinet for reliable opening and closing. Replace if cracked, broken, or missing to restore proper lid alignment.

This drain hose assembly routes defrost and condensation water from the evaporator to the refrigerator drain pan, preventing pooled water and ice buildup. Replaces a damaged or clogged hose to restore proper drainage and reduce leaks. What it does:

• Channels defrost and condensate water away from the evaporator area to the drain pan
• Restores normal drainage when the original hose is cracked, split, clogged, or collapsed
• Helps stop water pooling inside the fresh food or freezer compartments
• Reduces risk of ice build-up or odor caused by trapped water

• One drain hose assembly as shown

• Disconnect power to the appliance before starting any repair
• Remove any shelving or panels needed to access the evaporator and drain routing
• Ensure hose is seated securely at both ends and routed without kinks or sharp bends
• After installation, run a short manual defrost or pour water down the drain to verify proper flow

This replacement foot wheel is a single roller-style support that helps appliance doors/drawers glide smoothly and maintain proper alignment. Restores stable movement and prevents scraping or uneven wear on contact surfaces. What it does

• Supports and guides sliding motion for a door, drawer or appliance panel
• Reduces friction to improve smooth opening and closing
• Helps maintain alignment to prevent rubbing or binding
• Commonly replaced when wheel is cracked, worn, or causes noisy operation

• One foot wheel

• Remove power or disconnect appliance before servicing if required for access
• Inspect mating track or housing for damage and clean before installing
• Replace with like part and ensure wheel is seated securely in its bracket

This impeller mounting bolt and washer kit secures the washer/dryer or dishwasher pump impeller to the motor shaft, keeping the impeller aligned and preventing wobble or separation during operation. Designed for direct replacement to restore pump function. What it does:

• Fastens the pump impeller to the motor shaft so the impeller turns with the motor
• Prevents the impeller from loosening, reducing leaks, noise, and reduced water movement
• Helps restore normal pump performance when a worn or missing fastener allows slippage

• One impeller mounting bolt and matching washer

• Replace only when the pump is disassembled or impeller is being serviced
• Disconnect power and water before starting work to avoid shock or flooding
• Tighten to the manufacturer's specified torque if available; avoid over-tightening which can strip threads
• If other pump components show wear or damage, inspect and replace as needed for reliable operation

Replace broken or missing front leveling legs to stabilize your washer on uneven floors. Adjustable legs restore proper balance and level positioning.

Replacement spring for the washer's out-of-balance switch lever. It restores proper lever tension so the switch can correctly sense unbalanced loads and manage the spin cycle, helping reduce vibration, noise, and nuisance stops. What it does:

• Maintains the return tension on the out-of-balance switch lever so the switch actuates reliably during spin
• Allows the control to pause or redistribute when a load is unbalanced, minimizing vibration and banging
• A weak, stretched, or missing spring can cause no-spin, repeated pauses, or cycles that end early with out-of-balance warnings
• Helps ensure accurate imbalance detection for consistent spin performance

• Includes 1 spring

• Unplug the washer before servicing
• Access the out-of-balance switch lever (location varies by model; often under the top or behind the front panel)
• Note the spring's routing and attachment points; install the new spring in the same orientation and avoid overstretching
• After reassembly, run a short spin test with a small load to confirm operation

Captures lint and fabric fibers in your washer's drain system. Replace when clogged or damaged to maintain proper drainage and prevent blockages.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.