White Westinghouse Dishwasher Parts

This sump retainer secures the appliance sump assembly and helps keep the pump seal and surrounding components properly positioned to reduce leaks and maintain correct water flow. It's a small replacement part used during sump or pump repairs. What it does:

• Holds the sump housing or pump assembly in place to maintain a reliable seal
• Helps prevent water leaks from the pump/sump area when installed correctly
• Keeps internal components aligned for proper water circulation and drainage
• Commonly replaced when sump hardware is cracked, warped, or no longer secures the pump

• One sump retainer

• Power off and unplug the appliance before starting any repair
• Verify you have full access to the sump/pump area; removal of panels or racks may be required
• Inspect surrounding seals and gaskets; replace if damaged to ensure a watertight fit

A replacement switch mounting screw that secures control switches and switch assemblies in place for reliable operation. Replaces lost or stripped mounting hardware to restore secure panel and switch attachment on compatible appliances. What it does:

• Fastens the switch or switch bracket to the appliance frame or control panel
• Keeps electrical switch connections stable to prevent intermittent contact or movement
• Helps eliminate loose or rattling switches and noisy control panels
• Restores proper alignment of the switch for reliable user control

• Turn off power to the appliance before accessing the control panel to avoid shock
• Use the matching screwdriver size to avoid stripping the screw head
• Tighten securely but do not over-torque to prevent damage to the switch or panel
• Replace all affected fasteners for a secure fit

Red

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

This Shield is a protective cover used in select appliances. It helps guard nearby components and guide airflow or heat as designed, restoring proper protection when the original shield is cracked, warped, damaged, or missing.

• Acts as a barrier/deflector to protect components from heat, moisture, grease, or debris as designed for your model
• Helps maintain intended airflow, heat path, or splash control inside the appliance
• Replace if the shield is cracked, warped, burned, broken, or missing
• Symptoms can include visible damage, scorched or discolored areas near the shield, rattling/vibration, or exposed areas that were previously covered

• Disconnect power before servicing; also shut off gas
• Wear gloves—edges can be sharp on metal shields
• Reuse original screws/clips unless your model provides replacements
• Seat the shield flat and do not overtighten fasteners

This kickplate (toe plate) replaces the lower front trim on compatible refrigerators to restore appearance and protect the cabinet base from scuffs and drafts. Durable sheet-metal construction keeps the front edge looking clean. What it does:

• Covers and protects the refrigerator's lower front area from kicks, scuffs and dirt.
• Restores a secure trim piece when the original is bent, dented or loose.
• Helps reduce visible gaps at the cabinet base for a neater fit.
• Improves appliance appearance after damage or during refurbishment.

• Disconnect power to the appliance or follow the manufacturer's safety guidance before beginning work.
• Remove the old kickplate by loosening the retaining screws or clips; lift out and set aside.
• Align the replacement plate, engage any clips or tabs, and reinstall screws; avoid overtightening.

A replacement selector switch that restores user control of temperature and function selection on compatible ranges and ovens. Designed to match OEM fit and restore reliable control response for common cooktop/oven functions. What it does

• Selects oven or burner functions when you turn the control knob.
• Routes user input to the appliance control circuits so the unit responds correctly.
• Commonly replaces worn or failed switches that cause unresponsive controls, no function selection, or intermittent operation.
• Helps stop erratic behavior like controls that click without changing settings.

• Disconnect power to the appliance before beginning any repair.
• Replacement typically requires removing the control panel and knob; handle wiring and connectors carefully.
• Verify knob orientation and switch alignment during reassembly.

A replacement bearing that supports the dryer drum and restores smoother, quieter rotation. Replaces a worn or damaged bearing to help reduce noise and prevent excess drum play. What it does

• Provides a low-friction mounting point for the drum shaft to rotate smoothly
• Keeps the drum aligned and reduces wobble during operation
• Helps prevent metal-on-metal contact that causes grinding or rumbling noises
• Can reduce strain on the motor and belt by restoring proper drum support

• Disconnect power before beginning any disassembly
• Replacement typically requires removing panels and the drum;
• Inspect surrounding seals, shafts, and mounting hardware and replace if worn

This is a genuine replacement mounting screw used to secure appliance panels and components. It restores proper fit and helps prevent rattling or loose parts for safe, reliable operation. What it does:

• Fastens panels, trim pieces, or internal components to maintain proper alignment
• Secures parts that can vibrate or become loose during normal use
• Helps stop rattling, squeaks, or gaps caused by missing or damaged fasteners
• Suitable wherever the OEM specifies part 154041001 as the required screw

• Turn off and unplug the appliance before starting any repair
• Use the correct screw hole and match thread engagement; do not force or cross-thread
• Tighten firmly but avoid over-torquing to prevent stripped threads or cracked panels
• If multiple or different screws were removed, keep track of each location for correct reassembly

no.8 - 10 , 3/8 phillips