Michael S Pacifica , CA January 21, 2018 Appliance: Model KUDP02CRBS1 YEAR INSTALLED 2006 Kitchenaid dishwasher mod #kudp02crbs1 year 2006 front overlay quit working again! Our dishwasher quit working again for the 3rd time recently. We researched on You Tube for similar issue, and possible fixes. We had power to the overlay so we ruled out a thermal fuse as most possible problem. Some mode lights would come on when pushed. Tried a self diagnosis test-nothing. Reset circuit breaker-nothing. We had replaced the overlay once two years ago so thought this time it might be a Interconnect Board or a Electronic Board. After consulting with a rep (thank you Joyce) on the phone from AppliancePartsPros we decided to order all three parts and hope that it was one of them that was bad. Parts arrived in just two days, amazing!! I changed the Interconnect Board, still not working. Next decided to change the Overlay Board "again" and that fixed the problem. Not sure why the OLB went bad again for third time. Will keep new parts for now in case of future issues! Kitchenaid (Whirlpool) please take note, your Overlay Boards evidently are cheaply made!! First one lasted 9 yrs, second one barely two! Lets see how long the third one lasts!! Read More... 4 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Screwdrivers
Steven H Orlando , FL September 20, 2014 Dishwasher keypad stopped working I ordered a new keypad from AppliancePartsPros.com and installed it. It was pretty easy, just unscrew the front panel, unplug the old keypad, plug in the new one, put everything back into place and replace the screws. Much cheaper than having to buy a new dishwasher, and I made the repair myself! Delivery of the product was fast and I had the dishwasher up and running in 15 minutes! Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Dominick S Burbank , CA May 26, 2014 Appliance: KitchenAid Undercounter Dishwasher KUDP02CRBT3 The control panel was not working I unscrewed the panel on the inside then disconnected the electronics ribbon. Performed a test with my multimeter based the schematics on what each button should be send a signal to the corresponding ribbon wire. Found that the old panel was not working properly. Service technician was going to charge $93 for the part and $145 for the labor. I ordered through AppliancePartsPROS.com and got the part in 2 days ( I ordered after 3p so lost that and the next day) Part came as described and works wonderfully. I am very happy. Also extended warranty was $194 and Insurance Repai + 1 year warranty was $304. I saved a ton. Thank you very much AppliancePartsPROS.com Read More... 2 People found this story helpful Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Nut Drivers
Steve W Ashland , MA November 11, 2018 Buttons randomly worked and we could not run the dishwasher Ordered a new control panel and installed it in about 10 minutes, dishwasher works again. Read More... Do-It-Yourself Rating: Repair Time Estimate: Less than 15 minutes Tools: Screwdrivers
Charlene A Wellington , FL November 03, 2015 Overlay touch pad needed to be replaced Dishwasher is now working! Yippie! The ordering and the delivery of the part was fabulous. No problem. I did a DIY repair. Did a chat with a technician gave a little help but ended up figuring out how to remove the old one myself. The installation was literally a snap. One thing that would have helped if there was instructions on how to remove and install new part. Other than that I will continue to purchase my appliance parts from Appliance Parts. The diagram of the appliance and all its parts was great at ordering the correct part needed. Thank you. Read More... Do-It-Yourself Rating: Repair Time Estimate: 15-30 minutes Tools: Pliers