Whirlpool Blender Parts

This genuine refrigerator door gasket creates an airtight seal around the fridge door to help maintain proper temperature and energy efficiency. Replacing a worn gasket restores seal integrity and helps prevent moisture and frost buildup. What it does:

• Seals the refrigerator door to keep cold air in and warm, humid air out
• Reduces frost and moisture accumulation inside the compartment
• Helps the compressor run less often by maintaining proper cabinet temperature
• Commonly replaced when you notice air leaks, visible gaps, or a damaged/warped seal

• One door gasket (1 each)

• Inspect the cabinet flange and mounting channel for damage before installing
• Clean contact surfaces and allow gasket to warm/settle for an even fit; follow OEM seating procedure
• Replace with the door closed and check for even contact around the entire perimeter

This O-Ring is a small sealing gasket used in your appliance to create a secure, leak-resistant joint between mating parts. Replacing a worn ring restores proper sealing performance to help prevent drips, seepage, and premature wear. What it does:

• Forms a tight seal between mating components to contain fluids and protect internal parts
• Helps maintain proper system pressure and flow where used
• Reduces leaks at fittings, housings, or shafts
• Typical failure signs: visible seepage, persistent drips, or a flattened/cracked ring

• Includes one O-ring

• Disconnect power and shut off any supply lines before servicing
• Remove the old ring carefully; clean the groove and mating surfaces
• Apply a light silicone-based lubricant to the new ring
• Seat evenly without twisting; reassemble and tighten fittings without overtightening

This interlock collar assembly centers and supports the door/lid interlock so the appliance can detect and secure the door during operation. Restores proper engagement of the latch for reliable start/lock behavior and safety sensing. What it does:

• Positions and stabilizes the interlock/lock mechanism so the door or lid can latch correctly.
• Helps the appliance register a closed/locked door so cycles can start and run.
• A worn, cracked, or broken collar can lead to failure-to-start, door not locking/unlocking, or intermittent door-latch problems.
• Works with the interlock/latch components to maintain safe operation of the door/lid assembly.

• Disconnect power before attempting any service; follow basic electrical safety.
• Replacement requires access to the door/lid latch—use appropriate hand tools and avoid forcing plastic tabs.
• Inspect the interlock and latch components for additional wear; replace damaged parts as needed.
• Refer to OEM instructions for model-specific removal and reassembly guidance.

This replacement cap is a small protective cover designed to protect exposed openings and components from dirt, debris and moisture, helping maintain proper appliance performance and reduce wear. What it does:

• Covers and protects exposed shafts, fittings or openings to keep contaminants out
• Helps maintain seals and prevents debris buildup that can cause noise or premature wear
• Restores the part's finished appearance when the original cap is cracked, broken or missing
• Serves as a simple, low-cost repair to avoid secondary damage to adjacent components

• Disconnect power and water supplies before attempting any repair
• Typically presses or snaps into place; inspect mating surface for damage or buildup before installing
• Use appropriate safety gear and avoid forcing the cap onto a damaged part

This replacement jar restores a damaged or missing blender container so you can safely blend ingredients and transfer them without leaks or contamination. It fits the original coupling and seals when seated properly. What it does

• Holds ingredients for blending, mixing, and pureeing.
• Replaces jars that are cracked, chipped, leaking, or otherwise damaged.
• Restores a proper seal with the blender base to prevent leaks during use.
• Lets you resume normal blending performance when the jar is the worn or failed component.

• Ensure the blender is unplugged and the drive coupling is clean before installing the jar.
• Seat the jar fully on the base and the coupling engages smoothly.
• Inspect the jar and any gaskets or seals for damage; replace seals if explicitly required.
• Follow the appliance manufacturer's cleaning and care instructions for this part.

The Jar is an OEM part for Whirlpool blenders. This jar serves as the container where ingredients are placed for blending, mixing, or pureeing. This plastic jar measures approximately 8 inches wide by 10 inches high and has a capacity of 56 liquid ounces. The part includes the jar, blades, and bottom coupling. 

Causes of a bad jar can include cracks or chips from accidental drops, warping from exposure to extreme temperatures, or clouding and scratches from prolonged use. These issues can compromise the jar's structural integrity and affect the overall performance of the blender.

Symptoms of a bad Jar include:

• Leaks during blending
• Difficulty in attaching the jar to the base
• Visible cracks, chips, or warping
• Reduced blending efficiency due to a compromised seal

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Color: white. This attachment measures about 6 inches in diameter including the blades, and 4 inches high.

This 120V blender motor powers the blender base to drive the blades for chopping, pureeing, and mixing—restoring normal blending performance so the pitcher processes food and drinks reliably. What it does:

• Turns the blade assembly to blend, chop, and puree ingredients.
• Restores power when a bad motor causes the blender not to start.
• Helps eliminate weak or inconsistent blade rotation that leaves food unevenly processed.
• Resolves humming or stalled motor symptoms when the motor itself is the cause.

• Always unplug the appliance before servicing to avoid electrical shock.
• Basic hand tools may be required; keep track of fasteners and gaskets during disassembly.
• Confirm proper alignment of the motor coupling and blade assembly before reassembly.