Whirlpool Blender Parts

Blender won't blend or makes grinding noise? A worn drive coupler is often the cause. This motor-to-blade connector takes 5-10 minutes to replace.

The Jar is an OEM part for Whirlpool blenders. This jar serves as the container where ingredients are placed for blending, mixing, or pureeing. This plastic jar measures approximately 8 inches wide by 10 inches high and has a capacity of 56 liquid ounces. The part includes the jar, blades, and bottom coupling. 

Causes of a bad jar can include cracks or chips from accidental drops, warping from exposure to extreme temperatures, or clouding and scratches from prolonged use. These issues can compromise the jar's structural integrity and affect the overall performance of the blender.

Symptoms of a bad Jar include:

• Leaks during blending
• Difficulty in attaching the jar to the base
• Visible cracks, chips, or warping
• Reduced blending efficiency due to a compromised seal

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Connects the blender motor to the blade assembly. Replace if stripped, cracked, or worn from overloading or blending hard ingredients without liquid.

Seals the blender jar base to prevent leaks during blending. Replace if you notice liquid leaking from the bottom. Confirm fit with your model number.

This drive coupling connects the motor shaft to the blender jar. Replace if worn, stripped, or cracked to restore proper blade rotation and function.

Seals blender jar to base preventing leaks. Replace if cracked, worn, or leaking occurs. Confirm fit with your model number before ordering.

This washer lid assembly replaces a cracked, broken, or misaligned lid so the washer can close and lock correctly, restoring safe operation and reducing cycle interruptions caused by a lid that won't align or latch.

• Covers the tub opening and aligns with the lid lock/strike for proper engagement
• Restores the safety interlock so wash cycles can start and run without interruption
• Helps contain splashing and keeps debris out of the washer when not in use
• Typical symptoms include visible cracks or shattering, warped or loose lid, broken hinge area, or intermittent lid-lock errors

• Disconnect power before servicing
• Protect the cabinet surface and support the lid during removal/installation to prevent damage
• If required by your model, transfer existing hinge hardware and fasteners to the new lid
• After installation, check alignment and ensure the lid lock engages smoothly before running a cycle

Replacement pusher for food processor feed tube. Guides ingredients safely down the chute and engages the cover interlock. Replace if cracked, broken, or missing.

Seals the motor shaft opening to prevent liquids from entering the housing. Replace if you notice leaks or moisture around the base. Verify fit with your model.

Keeps rotating shafts aligned for smooth, quiet operation in your food processor. Replace when you notice noise, friction, or wobbling during use.

This genuine refrigerator door gasket creates an airtight seal around the fridge door to help maintain proper temperature and energy efficiency. Replacing a worn gasket restores seal integrity and helps prevent moisture and frost buildup. What it does:

• Seals the refrigerator door to keep cold air in and warm, humid air out
• Reduces frost and moisture accumulation inside the compartment
• Helps the compressor run less often by maintaining proper cabinet temperature
• Commonly replaced when you notice air leaks, visible gaps, or a damaged/warped seal

• One door gasket (1 each)

• Inspect the cabinet flange and mounting channel for damage before installing
• Clean contact surfaces and allow gasket to warm/settle for an even fit; follow OEM seating procedure
• Replace with the door closed and check for even contact around the entire perimeter

Replace your cracked or damaged blender jar to restore leak-free blending. This container holds ingredients securely and fits the original coupling. Confirm fit with your model number before ordering.

Replacement glass jar for blenders. Installs on the base and secures to the blade assembly. Replaces cracked, chipped, or leaking pitchers.

Protective cap for blenders that covers exposed shafts and openings. Replace if cracked, broken, or missing to prevent dirt and debris buildup.

Replace your food processor bowl seal when you notice leaking or decreased performance. Ensures tight seal between bowl and base. Verify fit with model number.

Replacement spatula accessory for your food processor. Used to scrape ingredients from the bowl. Order a new one if your original is lost or damaged.