Whirlpool Washer Dryer Combo Parts

This drum baffle restores the internal lift inside the dryer drum to help separate clothes and promote even tumbling. Replacing a cracked or missing baffle can reduce banging noises and help restore consistent drying performance. What it does:

• Lifts and moves clothes for more even tumbling and airflow inside the drum.
• Helps prevent garments from bunching or wrapping around the drum during a cycle.
• A damaged or missing baffle can cause loud thumping, scraping noises, or uneven drying; replacing it addresses these common symptoms.
• Designed to match the OEM drum mounting points for proper fit and function.

• Disconnect power (and gas, if applicable) before servicing the dryer.
• Access typically requires removing the dryer front or drum; keep track of fasteners and take photos for reassembly.
• Use basic hand tools and avoid forcing parts; inspect mounting hardware and drum condition while replacing the baffle.

This white top console replaces a damaged or faded console on compatible Whirlpool laundry appliances, restoring the control-area appearance and providing a clean mounting surface for the control panel and knobs. Designed to match factory fit and finish. What it does:

• Replaces cracked, dented, or discolored top console to improve appearance and protect internal controls
• Provides the mounting surface and alignment points for the control panel and user interface components
• Helps reduce dirt and moisture entry into the control area when properly installed
• Restores proper spacing and clearance for knobs, buttons, and display bezels

• Always disconnect power to the appliance before starting work
• Basic hand tools are typically required; follow factory service instructions for removal and reassembly
• Support the console while removing fasteners to avoid dropping or scratching the part
• Secure all fasteners; test controls after reassembly

This push-to-start replacement knob restores a worn, cracked, or missing control knob so you can easily engage your range/oven functions. Matches the original shape and feel for a secure, intuitive push action. What it does:

• Replaces a broken or loose push-to-start control knob so buttons and switches engage properly
• Provides a correct fit and turning/pushing feel to operate cooking controls
• Restores cosmetic appearance with the biscuit finish
• Helps prevent control slippage or uncomfortable operation caused by damaged knobs

• One push-to-start control knob (biscuit color)

• Always disconnect power to the appliance before attempting any replacement
• Pull the old knob straight off the control shaft and push the new knob on until fully seated
• If knob feels loose after installation, check the control shaft for damage—replace shaft or control if needed
• No special tools typically required;

This control panel overlay is the printed front cover that restores button labels and the finished appearance of the appliance console. It helps make controls readable and gives the console a like-new look. What it does:

• Covers the appliance console with printed button labels and icons for user controls
• Replaces faded, scratched, or peeling front graphics that make buttons hard to read
• Restores a clean, visually accurate control surface for normal operation
• Helps protect the underlying control components from light wear and cosmetic damage

• One control panel overlay

• Disconnect power at the breaker or unplug the appliance before starting any work
• Remove the console or access panel to avoid damaging snaps or clips
• Peel off the old overlay and clean the surface fully before aligning and securing the new overlay
• If adhesive backing or clips are involved, verify correct alignment before final adhesion

A small retainer clip that secures panels, hoses or wiring to keep components in place and reduce noise from loose parts. Replacing a worn or broken clip restores proper fit and helps prevent intermittent contact or rattling. What it does

• Secures trim, panels, hoses or wire harnesses to mounting points to prevent movement.
• Keeps components aligned so switches and seals engage correctly.
• Stops rattling or vibrating noises caused by loose parts.
• Helps prevent abrasion or chafing of wires and hoses by holding them away from edges.

• Install by snapping or sliding the clip into the factory mounting slot; use needle-nose pliers if needed.
• Power off and unplug the appliance before accessing internal parts.
• Inspect surrounding mounts and mating tabs for damage; replace if worn for a secure fit.
• If removal is difficult, apply a small amount of penetrating lubricant and work carefully to avoid breaking adjacent plastic.

This water inlet valve assembly controls water flow to the refrigerator's dispenser and ice maker, restoring reliable water delivery and stopping leaks or no-water issues when the original valve fails. What it does:

• Opens and closes to supply water to the ice maker and door dispenser
• Allows proper water pressure for filling ice maker trays and dispensing
• Stops water flow when closed to prevent leaks or overfilling
• Faulty valves can cause no water from dispenser, slow fill, continuous running, or leaks

• One water inlet valve assembly

• Disconnect power and shut off the water supply before service
• Verify fittings and tubing are seated and tightened to avoid leaks
• Replace only with matching part number and test for leaks after restoring water/power

This outer refrigerator door replaces a damaged or worn exterior door panel so your fridge seals and looks like new. It restores proper closure and helps maintain internal temperature control and appliance appearance. What it does:

• Replaces a damaged, dented or cracked outer refrigerator door panel
• Restores a straight, secure door edge for better sealing and operation
• Helps prevent cold air loss that can cause temperature fluctuations
• Improves appliance appearance by replacing scratched or faded exterior finish

• One outer refrigerator door panel

• Disconnect power and empty the door before starting; remove any screws or hinge covers securing the door
• Lift or support the door while removing hinge fasteners to avoid dropping or damaging the cabinet
• Align hinges and test door swing and seal before tightening all fasteners
• If inner components (bins, trim, gaskets) are attached, they should be properly reinstalled or transferred per manufacturer instructions.

Kit includes 2 sleeves.