White Outdoor Chore Performer

This replacement part is a hex nut. This is a genuine replacement part made by MTD. Hex nuts are small but important to the overall workings of many appliances. These parts work with other small pieces such as screws and washers to ensure that all parts of the machine are secure during use.A new hex nut might be needed if the current one is missing or damaged in any way. This can be caused by normal wear and tear with years of extended use. Hex nuts can experience large amounts of friction over time and may become stripped down. Be sure to replace the part as it might not be as effective as in prior uses. Refer to the user manual for specific directions on how to replace this part.This hex nut is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This replacement part is a coupling shield. This is a genuine replacement part made by MTD. This small part is important to many different types of machinery. This part is commonly used to assist pipes in or around the engine so that everything is able to run smoothly and effectively. A new coupling shield might be needed if the parts are no longer holding in place. Wear and tear over time can cause the parts to become loose. If this is the case, they should be replaced or repaired. Coupling shields are made of durable metal and will last a long time. Be sure the engine is shut down and cooled off before replacing this part. This part is also a genuine OEM replacement part to ensure proper fit. This part is sold individually and is sourced directly from the manufacturer for long-lasting use.

This is a replacement discharge chute for lawn mowers, wood chippers, and snow blowers. The discharge chute allows for debris to be be propelled away from both the machine and operator. The chute can filter wood chips, snow, and grass clippings.Over time, because of wear and tear, a discharge chute can break. This can also occur from damage should the chute be bumped against walls, siding, and other solid surfaces. Damage can also occur when running over hazardous materials such as rocks, clumps, and sticks. Replacing the discharge chute is rather simple, however, it does depend on the type and model of the machine. Lawn mowers for example are simple pop-on attachments, where as wood chippers require some tools and assembly.This is a genuine OEM replacement discharge chute. This part is compatible with MTD, Craftsman, and White Outdoor products. This part is sold separately.

This genuine OEM part is a compression spring for a lawnmower. The compression spring is the spring that holds the mower deck onto the lawnmower. Over time, the compression spring can become degraded due to excessive wear and tear. If it is no longer securing the mower deck, it will need to be replaced. Luckily, replacing this part is a relatively simple process.To replace the spring, make sure the mower deck is set to the lowest position. Locate the old retainer spring and pull it out and away from the mower. Once removed, slide the new spring into its proper position. Make sure it fits tightly, and the mower deck is secured. Once secured, power the mower to see if the spring stays in place during operation. If it does, then the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

This replacement part is a washer. This is a genuine replacement part made by MTD. This part is small but important in many different types of machinery and appliances. Washers work together with other small parts like screws to help keep pieces attached securely and safely. A new washer might be needed if the current one is missing or damaged. It is possible that over time washers can become worn down due to friction coming from the parts around them. If this is the case, it is recommended that it be replaced. Be sure to purchase the correct amount of washers as many appliances require more than one to operate effectively. This part is sold individually and is sourced directly from the manufacturer. This part is a genuine OEM replacement part to ensure proper fit and long-lasting use.

This is a genuine replacement OEM throttle control cable. The throttle control cable is comprised of an internal wire that slides through the external housing. Force is transferred from the accelerator pedal to the control linkage mounted to the throttle body from this sliding movement. If constant speed is not being maintained from the cruise control or delays starting, stopping, or jerking, then it may be time to replace the throttle control. To replace the throttle control a pair of pliers is needed. Remove the cable housing using pliers. The housings will swivel off the base and slide down the cable. Next, thread the cable wire through the housing. Locate the wire base on the back of the engine and run the cable through the throttle base and throttle arm. With the throttle all the way down, slide the cable through the housing and into the handle unit to attach it to the throttle handle. Pull the cable with a pair of pliers to make it tight and turn the lock screw. Replace the throttle to test the tension. If the mower, edger, or trimmer is running too high then loosen the cable.This throttle control works with lawn mowers, edgers, and trimmers. This is an OEM part sourced directly from the manufacturer and sold individually.

This OEM part is a depth cable for lawnmowers. Also known as a stop cable, the depth cable is the cord that stops the blades from running when the mower is in an idle position. If the lever has been released and the blades are still rotating, this might mean that the depth cable is no longer functioning and needs to be replaced. Luckily replacing the depth cable is a relatively simple fix. To replace the depth cable, begin by removing the bracket that holds the cable to the handle by using a screwdriver to pry it off. On the lower part of the handle, there is a clip that secures the cable. Remove the clip and disconnect the end of the cable near the kill handle. Locate the brackets connected to the engine. Remove the plastic tabs securing the cable housing with a pair of needle-nose pliers and pull the housing away from the bracket. Set the old cable aside and reinstall the new cable in reverse order. This genuine replacement part is sold individually and is compatible with MTD brand lawnmowers.

This replacement part is a tiller flap intended for use on lawn mowers. It protects the user and equipment from flying debris that might cause harm during use.A new tiller flap might be needed if the current one is missing or damaged at all. This can include the part being torn, bent, or cracked in any way. This part can be damaged after years of normal wear and tear and should be replaced if this is the case. Be sure the engine is powered off before attempting to replace or repair this part. This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This replacement part is a pinion drive. It is a genuine replacement part made by MTD. This part is typically found in chainsaws and helps the spinning and turning mechanism of the chain to operate properly while in use. A new pinion drive might be needed if the user notices that the chain in the chainsaw is not rotating properly. This can be due to a stripped pinion drive and the problem should be fixed once the part is replaced. It is common that this happens after years of normal wear and tear. Be sure to wear work gloves as the user will be working close to the blades in the chainsaw. Refer to the user manual for more detailed information on this part. This pinion drive is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer to ensure proper fit.

This drive pulley is a genuine MTD part, sold individually. This drive pulley can be used as a replacement part in a snowblower or an edger. This part is used in conjunction with the drive belt to move the appliance.The drive pulley in a snowblower or an edger might have to be ordered as a complete replacement part in a drive pulley that can no longer generate rotation in the wheels of the appliance. This could occur if the drive pulley has suffered damage from general wear and tear with long-term use or as the result of a collision with a hard object such as a rock or a curb.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This drive pulley is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Yard Machines, Montgomery Wards, Yard Man, and MasterCut.

This replacement part is a shredder blade. This is a genuine replacement part made by MTD. This blade is commonly found in lawn mowers and is used to shred grass effectively and smoothly during use. A new shredder blade might be needed if the machine is no longer shredding grass or mulch as effectively. If the blade has been used for a while, it is possible that it has become dulled down over time. If this is the case, it is recommended that the blade be replaced to return the appliance to working order. Wear work gloves when replacing this part as the blade is sharp. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

This part is a throttle control box assembly. The throttle controls the amount of air or fuel that enters the engine and also controls the speed of the engine. This assembly includes a throttle control knob that allows the user to control the throttle and the speed of the outdoor power equipment machine.A new throttle control box may be needed if any part of the assembly is cracked, broken, or damaged in any way. It's important to remember to wear gloves when operating or performing care and maintenance on any outdoor power equipment machines.This part is a genuine MTD throttle control box assembly and is an OEM part sourced directly from the manufacturer and it is sold individually. This specific throttle control box assembly is compatible with edgers and lawn tractors that are manufactured by MTD, Yard Man, Yard Machines, and Cub Cadet.