Yard Machines Log Splitter Parts

Seals the dipstick oil fill tube on mowers and small engines. Replace if leaking oil or cracked to prevent engine damage. Confirm fit by model.

Seals carburetor to insulator plate, preventing fuel leaks. Replace when worn, cracked, or torn to restore engine efficiency. Verify fit with your model.

This replacement part is an oil seal. This is a genuine replacement part made by MTD. This part is used to ensure that oil and other fuel cannot escape from the tank. The seal prevents it from leaking during use to ensure the engine is able to run properly. A new oil seal might be needed if the current one has been damaged. If the seal is worn down and thinner than before, it can cause leaks and oil waste. If this is the case, the seal should be replaced immediately. Oil leakage can cause other issues within the machine. Refer to the owner's manual for more information on how to replace this part. This is a genuine OEM replacement part. This part is sold individually and is sourced directly from the manufacturer.

Connects piston to connecting rod inside the engine cylinder. Replace if pin is stripped, worn, or missing to restore proper piston assembly and movement.

Oil fill tube assembly for small engines on mowers, tillers, and chippers. Replace if cracked, damaged, or leaking. Installs on engine block.

This is an MTD rocker arm. The rocker arm works in conjunction with the engine and head. The job of the rocker arm is to push the intake valve open, allowing fuel and air to enter the cylinder. Since the rocker arm is a part of the head gasket system, any damage can cause the engine to run extremely weak. There could also be a noticeable clicking or ticking noise originating from the engine area of the mower. A visual inspection of the rocker arm will confirm any damage. Begin the repair by removing the muffler guard. After removal, move to the valve cover and remove that guard as well. Disconnect the fuel and air lines running to the head. Remove the spark plugs in the valve section. Finally, the rocker arm can be removed using a socket wrench. Repeat these steps in reverse to install the new rocker arm.This product is sourced directly from the manufacturer as a genuine OEM part. The component is available individually, separate from the original machine. This part is compatible with MTD and Cub Cadet brand equipment.

Seals the intake valve to prevent oil leaks and maintain proper compression in small engines. Replace if you notice oil consumption or performance loss.

Intake valve seal prevents air and fuel from escaping during engine operation. Replace if you notice oil consumption or reduced performance. Verify fit with your engine model number before ordering.

Replaces a worn, damaged, or missing valve spring retainer in your outdoor power equipment engine. Essential small fastener component for valve assembly.

If your engine runs rough or won't start, the exhaust valve adjuster may need replacement. This part ensures proper valve clearance for optimal performance.

Exhaust valve spring installs in small engines to control valve operation. Replace if spring is broken, weakened, or missing to restore proper valve function.

Fix engine starting problems or loss of compression with this valve spring. Controls valve timing in small engines. Common repair for lawn tractors and snow throwers.

This replacement part is an oil seal. This part is small but important in various types of machines that rely on oil to run. The oil seal is found near the fuel tank and ensures that there are no leaks. If the machine is leaking oil, it can be due to a damaged oil seal. Seals like this one can wear out over time or be knocked out of place by impact.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

Replacement oil drain plug for small engines on outdoor power equipment. Needed when original plug is stripped, cracked, or leaking. Installs at oil pan.

This choke control lever automatically regulates the combined amount of air and fuel that come together in a small gasoline powered engine's carburetor to give a cold engine a fuel-rich mixture when the motor is first started. The control lever has several positions that allow it to adjust the fuel/air mixture in lawn equipment such as lawn mowers, snow blowers, tillers, chippers, log splitters, and other small gas engines. Over time with regular use, the control lever may become worn and must be replaced. There are several signs that indicate a choke control lever may be failing. If the gas tank is full of fresh gasoline but the engine refuses to start, if the engine starts and quickly floods, or if the engine runs at top speed but does not idle, the choke control level may be need to be replaced. Should the choke control lever need to be replaced, it is essential to use an OEM genuine manufactured replacement part such as this one. OEM parts are built to the exact specifications of the equipment's original parts. This part is compatible with Huskee, Cub Cadet, Yard Man, MTD, Yard Machines, and Troy-Bilt brand equipment.