Yard-Man Engine Parts

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

External gasket kit seals carburetor and engine surfaces on lawn equipment. Replace when you notice fuel leaks or loss of compression. Verify fit with your model.

Ignition coil for small engines on lawn and garden equipment. Replace if cracked, damaged, or worn. Includes spark plug boot and wire assembly.

Protects your mower's air filter from dirt and debris. Replace if cracked, damaged, or no longer securely holding the filter. Confirm fit with your model number.

Oil fill plug assembly for small engines. Seals the oil fill opening to prevent leaks. Replace if cracked, stripped, or missing to maintain proper seal.

Starter rope won't retract after pulling? This recoil pulley and spring assembly fixes rope retraction issues on mowers and small engines. Direct fit.

Carburetor gasket for walk-behind mowers. Replace when you notice fuel leaks, hard starting, or during carburetor service. Verify fit with your model.

Plastic primer bulb that draws fuel into the carburetor when pressed. Replace if cracked, broken, or no longer creating proper seal for priming.

Governor spring for snow thrower engines. Replaces worn, stretched, or missing springs that control engine speed regulation. Direct fit component.

This is a recoil starter assembly for lawn and garden power equipment. When the recoil starter rope is pulled, this causes the spark which starts the engine.A new recoil starter assembly will be needed if the recoil or pulley system has broken. The rope may become broken or frayed and the plastic on the pulley could crack. If the rope becomes loose and there is no tension when it is pulled, then a new recoil starter assembly will be needed.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. It is used on engines, lawnmowers, lawn tractors, and log splitters that are manufactured by MTD, Yard-Man, Yard Machines, Cub Cadet, Husky, and Troy-Bilt.

Carburetor assembly for snow thrower engines. Installs on the engine block to mix air and fuel. Replace if cracked, damaged, or leaking fuel.

This genuine OEM Part is a choke temperature control rod for lawnmowers. The choke temperature control is the metal piece that regulates the choke temperature allowing for it to function properly within a lawnmower. If the choke function is no longer working efficiently, it might be time to replace the choke temperature control. Luckily, replacing this part is a simple repair.Before beginning, make sure the engine is cool to avoid getting burned. Locate the old choke temperature control rod and remove the screws to the mounting assembly that hold the rod in place. Once removed, lift the old choke temperature control out and away from the mower and set it to the side. Replace with the new control rod and secure the mounting screws. Start up the mower to see if the choke function is working properly. If it does, the installation was a success. This replacement part is sold individually and is compatible with MTD brand lawnmowers.

Bell washer for lawn mowers and tractors. Installs to secure components and prevent loosening. Replace if cracked, worn, or missing for proper assembly.

Replace a cracked or broken ignition coil on your walk-behind lawn mower. This part sends power to the spark plug and may need replacement if damaged.

Governor return spring for small engines on lawn mowers, tillers, and outdoor power equipment. Replace if broken, stretched, or missing. Installs on engine.