Yard-Man Trimmer

This is a pawl assembly intended for use in many models of lawn and garden equipment. The piece attaches to the short block engine assembly. The pawls will lock onto the flywheel to start the engine when the starter turns and forces the pawls outwards. If there is a problem getting the engine started, the pawl is to blame.The pawl is made from plastic. While it is durable, parts of it could break or crack over time and with a lot of use. When servicing the machine and trying to locate problems that affect the way it starts, owners should check the pawl. A screwdriver and an Allen wrench can help with the replacement of this part.The pawl assembly is compatible with blowers and trimmers from Troy-Bilt, Yard-Man, Cub Cadet, and MTD. The piece is sold individually. It is a genuine OEM replacement part that has been sourced directly from the manufacturer.

This flex tube is a genuine MTD part sourced directly from the manufacturer. It is made as a replacement part for blowers. Especially since it is made of plastic, it is normal for it to need replacement from extended wear and tear.This is a relatively easy repair, although some disassembly of the engine and the equipment is required. To replace the flex tube on a blower, allow the engine to cool completely, disconnect the spark plug to prevent the equipment from accidentally powering on, and empty the fuel tank. Next, detach the blower nzle and extension tube. Loosen and remove the swivel blower tube, detach the cable clip, and remove the screws attaching the original flex tube. Replace the flex tube. Before ordering, inspect the blower to see if new screws are also needed.This flex tube is a genuine OEM part sourced directly from the manufacturer. It is compatible with machines made by Craftsman, Murray, Remington, MTD, Troy-Bilt, and Yard-Man. It is sold individually.

This genuine replacement part is a fuel tank assembly for use with a blower, leaf blower, or vacuum. It is also known as a fuel tank.This part is the fuel tank used to hold fuel in the leaf blower. The fuel tank assembly includes the fuel tank, fuel cap and the fuel lines. It is essential for safe and reliable use of the blower. Through extended use, this part may become worn out, cracked, or damaged. This can lead to a fuel leak, which can cause unsafe operating conditions. It is recommended to check the fuel tank periodically for any cracks or wear. Before working with this part, drain the gas tank into an approved storage container in a well-ventilated area. Prior to working with this part, please refer to the original product manual for a full list of included parts and installation instructions. For safety, always wear gloves and ensure unit is powered down prior to performing any installation or repair.This high quality OEM replacement part is sourced directly from the manufacturer, and it is sold individually. This part is compatible with Craftsman, MTD, and Troy-Bilt, Yard Man, and more blowers.

This replacement part is an insulator gasket. Insulator gaskets isolate the metal surfaces of a flanged joint, electrically insulating them.A new insulator gasket might be needed if the current one is damaged in any way. If the engine struggles to turn on or does not start at all, it might be due to a damaged or malfunctioning insulator gasket. When replacing this part, be sure that the engine is completely powered off and cooled down.This is a genuine OEM replacement part manufactured by MTD. This part is sold individually.

This part is a replacement air cleaner assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part is intended for use as a replacement for a broken, worn, or defective air cleaner assembly on various models of blowers. This air cleaner assembly includes the base, cover, and the foam air filter itself. This part helps to make sure that dirt, debris, and contaminants are filtered out of the air as it enters the engine so it doesn't have a negative effect on the equipment. Air filters should be cleaned regularly and replaced when worn or old. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to install this air filter assembly, the appropriate owner's manual and equipment diagrams should be referenced. This air filter assembly is a genuine OEM part made of durable materials and is sold individually. It is suitable for use with blower models that have been manufactured by MTD and Craftsman.

This replacement part is a gasket. It is a genuine replacement part made by MTD. This gasket is specifically found in leaf blowers and helps the engine run properly and smoothly. This part is an essential part of the appliance and may cause the entire machine to be out of commission if broken.A new gasket might be needed if the user hears unusual noises coming from inside the machine. If the appliance is having trouble being turned on or cannot turn off, it might be a faulty gasket. Be sure the engine is turned completely off before attempting this repair as usually this part is situated close to the engine. Refer to the owner's manual before replacing this gasket.This part is sold individually. This gasket is a genuine OEM replacement part and is sourced directly from the manufacturer.

The ignition module coil is part of a blower's ignition assembly. The coil inside the ignition module is charged by the flywheel. The module then sends this charge through the ignition wire and on to the spark plug to start the engine. If the ignition coil fails due to age or excessive use, the engine will not crank, and the ignition coil will have to be removed and replaced.Always wear work gloves and safety goggles when working on equipment. Remove the spark plug and empty the fuel tank. Remove the air filter cover and engine housing. Remove the fuel tank and ignition module cover. Disconnect the wires and take the screws out of the ignition module. Remove and dispose of the module. Install the new module and reconnect the wires. Reverse the process to reassemble the blower.This ignition module is sold as an individual unit. It does not come with screws. This module is designed for use in blowers manufactured by MTD, Craftsman, and Troy-Bilt. This is an authentic OEM part sourced directly from the manufacturer.

This throttle cable is a genuine MTD part, sold individually. This throttle cable can be used as a replacement part for a leaf blower or a leaf vacuum. The purpose of the throttle cable in a leaf blower or a leaf vacuum is to regulate the speed of the appliance so the pace can be determine by the operator. If the throttle cable has suffered damage in the form of fraying, tearing, ripping, puncturing, or eroding over general wear and tear from long-term usage, the throttle cable should be removed and replaced by this genuine OEM replacement part before using the leaf blower or leaf vacuum again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This is an OEM part sourced directly from the manufacturer. It is sold individually. This throttle cable is compatible with the following outdoor appliance brands: MTD, Craftsman, Yard Man, Troy-Bilt and Cub Cadet.

This replacement part is a bolt. This is a genuine replacement part made by MTD. Bolts are small but important to the overall workings of the machine. They work with other parts such as screws and nuts to ensure that certain pieces are held in place and are secure during use. A new bolt might be needed if the current one has become loose, is missing, or has been damaged in any way. If the bolt had been dented, bent, or logged in place, be sure to replace it as soon as possible. This should be a fairly simple repair and only require common household tools such as a screwdriver and pliers. This part is sold individually and is sourced directly from the manufacturer. This is a genuine OEM replacement part.

This screw and nuts set is a genuine MTD part, sold individually. This screw and nuts set can be used as a replacement part in a string trimmer. This set provides a variety of screws and nuts which serve as fastening components within the string trimmer.The screw and nuts set in a string trimmer might have to be ordered as a complete replacement part if one or more screws or nuts in the string trimmer has been lost, misplaced, or damaged. If this occurs, the screw and nuts set should be ordered as a genuine OEM replacement part.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This screw and nuts set is compatible with the following outdoor appliance brands: MTD, Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, Bolens, and Yard Man.

This o-ring is a genuine OEM part sourced from the manufacturer for use in many parts of engines in lawn and garden equipment. The o-ring is a type of gasket but is not flat like a gasket. It is circular and made of rubber. It is seated in a groove on the engine part and is compressed against another part to create a seal. This seal keeps air and fluids from entering or exiting the sealed part. Like gaskets, o-rings must be periodically inspected and replaced to ensure proper engine performance.Visual inspection of o-rings will reveal nicks, indentions, cuts, or tears on the surface of the o-ring. If the rubber has warped due to excessive heat, it will not fit properly and will need to be replaced. The replacement may not require tools, depending on the location of the rubber gasket. Remove the bad o-ring and wipe both sides of the area to remove the old grease. Apply fresh grease to the o-ring before installing it to ensure a tight seal. Press the new o-ring firmly in the groove before attaching the connecting part. If the ring does not seat well or has to be stretched to fit, discard and start with a new o-ring.The o-ring is sold individually. It is designed for trimmers and tillers. It is compatible with Craftsman, MTD, Bolens, Troy-Bilt, and Cub Cadet.