Parts for Magic Chef W205KGW: 01 - Base Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

10-24 x 1/2 inch mounting screw for securing appliance panels, handles, brackets, and internal components. Replace lost, stripped, or damaged screws.

Drive motor isolator.

Motor plate isolator.

This motor isolator is a rubber mounting that cushions and secures the washer motor, reducing vibration and noise during spin cycles and helping protect the motor and chassis from premature wear. What it does:

• Cushions the motor to reduce vibration and minimize rattle and noise during operation
• Keeps the motor properly positioned to prevent rubbing or misalignment
• Helps protect motor and surrounding components from shock and movement
• Common symptom linkage: excessive vibration, loud noise during spin, or visible motor shifting

• Disconnect power to the appliance before starting any work.
• This part mounts between the motor and chassis; access typically requires tilting or removing the washer cabinet or accessing the underside.
• Inspect adjacent mounts and fasteners; replace any worn hardware and use the exact OEM part for proper fit.

This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:

• Secures shafts, pulleys, or fittings to prevent axial movement
• Keeps assemblies fastened under normal vibration and load
• Helps stop wobble, grinding, or part separation caused by a loose connection
• Works with the matching threaded stud, shaft, or fitting for a proper hold

• Disconnect power and follow appliance safety procedures before servicing
• Use the matching thread size and engage threads fully; hand-start before tightening
• Tighten securely without overtightening; use the correct driver or socket for the nut
• Inspect mating threads and replace if damaged

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:

• Provides structural support to help keep assemblies aligned and reduce excessive movement
• Dampens vibration and minimizes knocking or rattling noises tied to loose components
• Restores proper fit where a worn or broken bracket allowed shifting or misalignment
• Works as a repair for symptoms like intermittent noise, excess vibration, or parts that sag or shift

• Disconnect power (and water if appliance-specific) before beginning any repair
• Basic hand tools are usually required; refer to your model's service manual for exact steps
• Inspect surrounding parts for wear while replacing the bracket

Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.

• Supports and self-levels the rear of the cabinet to maintain stability on uneven floors
• Helps address wobbling/rocking, excessive vibration, rattling or "walking," and an appliance that won't sit level
• Replaces a rear leg that is missing, cracked, or worn
• Promotes smoother operation by helping the unit sit properly level

• Disconnect power; if applicable, turn off the water supply
• With assistance, carefully tilt the appliance to access the rear base
• Remove the damaged rear leg from its mount and install the new leg, ensuring it seats fully
• Lower the unit, verify level with a bubble level, and adjust front legs as needed for final leveling

Replace a worn rear self-leveling leg to restore a stable, level appliance. This foot supports the back of the cabinet and automatically compensates for floor unevenness to help reduce vibration, rocking, and noise during operation.

• Supports and self-levels the rear of the cabinet to maintain stability on uneven floors
• Helps address wobbling/rocking, excessive vibration, rattling or "walking," and an appliance that won't sit level
• Replaces a rear leg that is missing, cracked, or worn
• Promotes smoother operation by helping the unit sit properly level

• Disconnect power; if applicable, turn off the water supply
• With assistance, carefully tilt the appliance to access the rear base
• Remove the damaged rear leg from its mount and install the new leg, ensuring it seats fully
• Lower the unit, verify level with a bubble level, and adjust front legs as needed for final leveling

This part has been discontinued by the manufacturer and is no longer available.

Includes leg, foot pad and locknut.

Snubber ring cushions the tub base during spin cycles. Replace if cracked, worn, or producing plastic shavings to restore smooth, quiet operation.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.