Parts for Maytag DF20J: 01 - Door Parts

Fixes loose panels, rattling doors, or wobbly components caused by stripped or missing screws. Secures brackets, covers, and mounting hardware. Easy DIY.

Seals the vent port on your freezer assembly to maintain proper containment. Replace if cracked, missing, or worn to prevent leaks and odors.

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

Mounting screw for freezer and refrigerator installations. Replaces lost, stripped, or damaged screws. Secures internal components and panels.

Creates an airtight seal to keep cold air in and warm air out. Replace if torn, cracked, or causing frost buildup. Confirm fit with your model number.

Thin shim that aligns and levels your freezer door at the hinge point. Replace when worn, damaged, or missing to eliminate rubbing and uneven gaps.

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

This lock assembly secures the appliance door/lid and enables normal cycle starts by engaging the latch. Replaces a worn or broken lock to restore proper door closure and allow the unit to begin and complete cycles reliably. What it does

• Physically latches the door/lid so the appliance can start and run
• Provides the mechanical engagement the control checks before permitting operation
• Common symptom: door won't stay closed or latch does not engage
• Common symptom: appliance won't start, won't advance or shows a door/lock fault

• Disconnect power (and water supply for washers) before beginning any service
• Handle small parts carefully and note their orientation for reassembly
• If wiring is present, disconnect and reconnect matching connectors only; do not force

Fastening screw for securing components inside appliances. Replaces lost, stripped, or damaged screws during repairs or part installations.

This is a replacement key used to operate an appliance key-lock or keyed latch, restoring access and security when the original key is lost or damaged. It provides a simple, low-cost way to regain normal use without replacing the lock. What it does

• Fits the appliance's keyed lock or latch to lock and unlock doors, panels, or compartments.
• Restores access when the original key is missing, worn, or broken.
• Helps secure control panels or storage compartments that use a keyed mechanism.
• Useful as a spare to prevent downtime from a lost key.

• Typically installs by inserting into the lock; no special tools required.
• Do not force the key—if it won't turn, check alignment or inspect the lock.
• If accessing electrical panels, disconnect power before opening the service area.