Parts for Maytag 61004753: 01 - Fountain Bracket Kit (115V) Parts

This part has been discontinued and is no longer available.

The Ice Door Fountain Kit is an OEM replacement part for Whirlpool refrigerators with built-in ice makers. It directs water to the ice molding trays and facilitates automated ice cube harvesting. Kit includes flapper, solenoid, strike arm, solenoid plunger, and instructions. Spring is not included. For the spring order 61004388.

Causes of a bad ice door fountain kit can include wear and tear over time, buildup of ice or debris obstructing the door mechanism, or damage to the components from frequent use.

Symptoms include:

• Incomplete ice cubes or low ice yield
• Drips or leaks in the ice maker area
• The ice drawer fails to eject cubes fully

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

This knurled pin secures the juicer cone and helps transmit torque for proper juicing action. It replaces a worn or damaged roll pin to restore stable cone alignment and smooth operation. What it does:

• Secures the juicer cone or attachment to the drive shaft to prevent slipping
• Transfers rotational force from the motor to the juicer cone
• Helps stop wobble, misalignment, or intermittent engagement of the juicer cone
• Commonly replaced when the pin is bent, worn, or broken

• One knurled pin

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Remove the juicer cone and any retaining parts per the service diagram before replacing the pin
• Use appropriate hand tools; avoid excessive force which can damage the shaft or housing

This ice door spring restores the closing tension on the dispenser chute door. Replacing a fatigued spring helps the flap seal properly after dispensing, reducing warm-air leaks that cause frost buildup and ice clumping around the chute. What it does:

• Provides return tension so the ice chute door closes after dispensing
• Helps maintain a tight seal to limit frost, condensation, and air leaks
• Can resolve a chute door that sticks open/closed or won't fully close
• Reduce rattling or poor ice flow caused by a loose flapper

• 1 spring

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control panel to access the ice door assembly
• Note spring orientation on the flapper; transfer/install carefully without over-bending
• Smooth flap movement and a proper seal before reassembly

• Dispenser door spring
• Flapper spring
• Ice chute door spring

2 terminal interlock switch.

This is the main electronic control board that manages the appliance's functions and user commands. It restores proper electronic control when the original board fails or malfunctions. What it does:

• Interprets commands from the console and controls cycles, timers, and key functions
• Powers and sequences motors, valves, heaters, and other driven components as designed
• Can resolve unresponsive controls, incorrect cycle behavior, or intermittent operation
• May clear display errors or communication faults when the board is the root cause

• (1) main control board assembly

• Disconnect power at the breaker or unplug the appliance before starting any work
• Handle the board by the edges; avoid touching components or connector pins to prevent static damage
• Transfer any brackets, harnesses, or mounting hardware from the old board only if present and required

Size: 8-32 x 1/4 inch.

The Ice Door Fountain Kit is an OEM replacement part for Whirlpool refrigerators with built-in ice makers. It directs water to the ice molding trays and facilitates automated ice cube harvesting. Kit includes flapper, solenoid, strike arm, solenoid plunger, and instructions. Spring is not included. For the spring order 61004388.

Causes of a bad ice door fountain kit can include wear and tear over time, buildup of ice or debris obstructing the door mechanism, or damage to the components from frequent use.

Symptoms include:

• Incomplete ice cubes or low ice yield
• Drips or leaks in the ice maker area
• The ice drawer fails to eject cubes fully

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

The Light Bulb is an OEM part for Whirlpool refrigerators. This part illuminates the water and ice dispenser area, providing visibility and ease of use, especially in low light conditions. 

Over time, the light bulb can fail due to normal wear and tear, electrical surges, or damage from vibrations and impacts. 

Symptoms of a bad light bulb include:

• The dispenser area not lighting up when activated
• Flickering or dim lighting
• The bulb failing to turn on consistently

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Size: 8-32 x .312 inch.

Water inlet valve kit replaces older valves that used the "Y" type water lines.

The Water Inlet Valve Assembly is an OEM part for Whirlpool refrigerators. This assembly controls the flow of water into the refrigerator's ice maker and water dispenser, ensuring that water is supplied efficiently and consistently.  

Causes of a bad water inlet valve assembly can include mineral buildup, wear and tear over time, electrical malfunctions, or damage from freezing.  

Symptoms of a bad water inlet valve assembly include:

• The ice maker not producing ice
• The water dispenser not dispensing water
• Leaks or puddles forming around the refrigerator
• Unusual noises coming from the valve area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Compression nut for 5/16" plastic water line.

Size: 1/4 inch. Nut for plastic water line.