Parts for Electrolux ELFE743CAT0: 02 - Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

Replace your dryer's exhaust duct assembly if cracked, damaged, or missing. Routes air from the dryer to the vent outlet for safe, efficient operation.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

If your dryer runs too hot, won't heat properly, or shuts off unexpectedly, the inlet thermistor may have failed. This sensor monitors incoming air temperature.

Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.

Replace your dryer's drum assembly if it's cracked, dented, or worn. This rotating cylinder holds and tumbles clothes during the drying cycle.

This is a left-side access panel in a titanium finish that forms part of the dryer's outer cabinet. It provides structural support and protects the internal components from dust and debris. Replace this panel if it is dented, cracked, rusted, or if the finish is damaged.

Secures internal components in your dryer. Replace this mounting bracket if cracked, broken, or missing to restore proper alignment and stability.

Control panel for your dryer. Mounts on the front of the unit and houses the control interface. Replace if cracked, damaged, or worn from regular use.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replaces cracked or broken air flow deflector baffle inside your dryer drum. Guides internal airflow for proper ventilation and cooling performance.

White molded baffle that lifts and tumbles laundry inside the dryer drum. Replace if cracked, broken, or missing to restore proper load movement.

Positioning spacer that maintains proper gaps between dryer components. Replace if cracked, broken, or missing to prevent parts from rubbing together.

If your dryer drum won't turn or makes grinding noises, a worn drive shaft may be the cause. This metal shaft transfers motor torque to rotate the drum.

Replacement drum support roller wheel assembly for dryers. Installs on bulkhead to support and guide drum rotation. Replace when worn, cracked, or loose.

Metal mounting nut secures panels, brackets, and assemblies on your dryer. Replace if cracked, stripped, missing, or causing loose components.

Adjustable leveling leg stabilizes your dryer on uneven floors. Replace if cracked, broken, or worn from vibration and repeated adjustments.

Dryer bulkhead that forms the front panel structure and houses the door seal. Replace if cracked, warped, or causing air leaks. Confirm fit with your model.

Fixes steam cycle not working or water not entering drum during steam cycles. Controls water flow into dryer. Moderate DIY repair for steam dryers.

Rubber grommet cushions wiring, tubes, or panels in your dryer. Replace if cracked, worn, or missing to prevent chafing and reduce vibration noise.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Hex washer head ,10-32 x 0.375. Ground

Fix unresponsive controls or intermittent power issues. This wiring harness restores electrical connections between the control board and components.

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.