Parts for Maytag LCRE655: 02 - Control Panel Parts

Control knob that replaces a damaged or missing appliance dial to restore simple, reliable selection of temperature or cycle settings. Provides a secure grip and clear position control for everyday use. What it does:

• Replaces cracked, worn, stripped, or missing control knobs so you can select settings reliably.
• Mounts on the appliance control shaft to allow accurate pointer alignment and selection.
• Reduces slipping, spinning, or inconsistent selection when turning the dial.
• Restores the user interface so controls are easier and safer to operate.

• Disconnect power to the appliance before servicing controls.
• Most knobs simply pull off the control shaft and the replacement presses on until seated.
• If the original knob used a set screw or retaining clip, save and reinstall that hardware.
• If the knob does not seat easily, stop and verify shaft type and fit to avoid damage.

This replacement thermostat knob mounts on the control shaft to set cooking temperature. It restores a secure grip and clear pointer so you can choose settings reliably when the original knob is cracked, stripped, or missing. What it does:

• Attaches to the thermostat/control shaft to adjust temperature settings
• Provides a clear pointer and tactile grip for accurate selection
• Can help resolve issues like slipping, not engaging the stem, or worn/illegible markings
• Helps restore consistent temperature adjustment when the original knob is damaged or missing

• One thermostat control knob

• Turn the appliance off and allow surfaces to cool before servicing
• Pull the old knob straight off the shaft—do not pry against the control panel
• Align the new knob with the shaft orientation/indicator and press on until fully seated
• Verify the pointer aligns with the Off/temperature marks and turns smoothly through the range

This indicator light installs in the control panel and illuminates when its corresponding function is active. Replace a failed lamp to restore clear status indication, so you can see at a glance when the appliance is operating.

• Lights to indicate a selected function is on (e.g., surface units or oven circuits—varies by model)
• Provides visual confirmation of appliance status during use
• Common symptoms: light will not turn on, stays on constantly, flickers, or the lens is damaged
• Restores proper visual feedback when controls are engaged

• Disconnect power at the breaker before servicing; allow the appliance to cool
• Access the console/control panel and remove the rear cover as needed
• Note wire positions; transfer leads to the new light and secure it in the panel opening
• Reassemble and restore power to test operation

This seal strip replaces a worn or damaged door gasket edge to restore a proper seal and help the appliance maintain temperature and operate quietly. It's a direct-fit service part used where a continuous seal is required. What it does:

• Provides a flexible barrier along the door/frame to reduce air leaks and heat/cold loss
• Helps prevent moisture buildup and improves energy efficiency when sealing is restored
• Reduces rattling and vibration caused by a compressed or torn seal edge
• Commonly replaced when the strip is torn, missing, or no longer adheres properly

• One seal strip

• Disconnect power to the appliance before servicing to avoid electrical or burn hazards
• Clean and dry the mounting surface; remove old adhesive or residue for best adhesion
• Align the strip carefully and press firmly; allow any adhesive to cure per manufacturer instructions

This spacer maintains the correct gap between mating components inside your appliance, keeping parts aligned and operating smoothly. Replacing a worn or missing spacer restores proper fit and helps prevent rubbing, noise, and premature wear. What it does:

• Sets and preserves the correct stand-off between components for proper alignment
• Helps ensure smooth operation and consistent control feel
• Reduces friction and contact that can cause noise or wear
• Common failure signs: loose or wobbly parts, rubbing/scraping sounds, misalignment, poor fit

• 1 spacer

• Disconnect power and, if applicable, shut off gas supply before servicing.
• Note the orientation of the original spacer and match it during reassembly.
• Handle nearby trim and control components carefully to avoid damage.
• After reassembly, verify smooth operation and proper clearances before restoring power/gas.

Color: Black

This infinite switch controls the heat level of an electric range's surface burner, letting you adjust burner temperature from low to high. Replace a worn or failed control to restore variable heat regulation for safe cooking performance. What it does:

• Regulates electrical current to the surface burner so you can set low-to-high heat levels.
• Restores variable burner control when heat is stuck on a single setting or won't cycle.
• Addresses symptoms like no heat at some settings, inconsistent burner temperatures, or a burner that only works on one or two settings.
• Works as the user-operated control behind the range control knob for a single surface element.

• Disconnect power at the house breaker or unplug the range before servicing.
• Verify correct replacement by matching terminal layout and mounting to the old switch; only install the exact part specified for your model.
• Use proper tools and avoid touching live terminals; Handle glass-top ranges carefully to avoid cracking when accessing or replacing the switch.

The Whirlpool Infinite Switch is an OEM part for Whirlpool ranges. Whirlpool electric ranges. This switch controls the multiple heat settings of the small element, allowing the user to select their desired cooking temperature. It is an important electrical component that regulates burner heating cycles.

Symptoms of a bad infinite switch include:

• The element not heating up adequately or failing to maintain temperature
• Inability to select or change heat settings on the
• Burner operates intermittently or fails to heat properly

Causes of a bad infinite switch can include failure over many heating cycles. The electrical contacts within the switch may become corroded or deteriorate from repeated exposure to cooktop temperatures and cooking residue.

It is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric range models.

This part has been discontinued by the manufacturer and is no longer available.